Citizen D710/D716 instruction manual Installing the USB Driver, Windows98 or Windows98 SE

Page 87

(3)Fully open the locking tabs of the communication unit and remove the watch.

*When using the communication unit to charge the watch for the first time, the Install Wizard of the USB driver is displayed on the personal computer display when the communication unit is connected to the personal computer. Refer to “3. Installing the USB Driver” for information on installing the USB driver.

*When attaching or removing the watch to or from the communication unit, make sure to fully open the locking tab of the communication unit. Attempting to attach or remove the watch without the locking tab fully open can cause the connection pins to become worn resulting in poor connection.

*If the metal band of your watch is too short so that the watch cannot be attached to the communication unit, remove the communication unit leg (removable) and fit the watch onto the communication unit by passing it over the location where the stand was removed to attach it to the communication unit.

3. Installing the USB Driver

In the case of performing data communication with a personal computer using the communication unit, a USB driver must be installed in the personal computer to be used in advance. Install the USB driver from the CD-ROM provided with the watch by following the procedure described below. The procedure differs slightly depending on the compatible OS.

*The display screens used in this explanation differ depending on the language and version of the OS.

Windows98 or Windows98 SE:

(1)Confirm that your personal computer has started up normally.

(2)End any applications that are currently running on the PC.

(3)Place the CD-ROM provided in the CD-ROM drive of the PC. If the AQUALAND GRAPH Nx installation menu is displayed at this time, click on the "EXIT" button to close this menu.

(4)If the communication unit is connected to the USB port of the PC, a message is displayed on the PC indicating that new hardware has been detected and that the PC is searching for the required application software.

Once this check of new hardware is completed, the "Add New Hardware Wizard" is displayed.

87

Image 87

Contents D710/ D716 Page English English English English Before UsingIntroduction Important Notes Safety Precautions Observe at All TimesGeneral Cautions Regarding Diving Page Page Page Contents Page Using the Scuba Diving Log Mode and Skin Diving Log Mode Watch Checking Accessories Prohibited Prohibited Use During Diving Page Page Various watch functions can be set on your PC FeaturesOther Convenient Functions This watch is of the rechargeable typeNames and Functions of Components ChargerPcs. of size AA Alkaline Batteries Installation Procedure Charging the Watch Watch Display During Charging Standard Mode Names of ComponentsWatch Display Modes Functions Dive Mode Dive Plan ModeScuba Diving Log Mode Skin Diving Log ModeUsage time Charge Level Indicator and Continuous Usage TimeHow to Read the Charge Level Indicator of the watch Amount of ChargeContinuous Usage Time UsingUsingthetheELELLightLightSwitching the Mode Standard ModeDive Plan Page Day Display Using the Standard ModeUsing the Time Mode Switching the DisplaySetting the Time and Date Daily Graphic Display Using the Travel Time Mode Setting the Travel TimeNormal Display Time Difference Display During interchanging ProcedureBefore Interchanging After interchangingDisplay Using the Destination Timer ModeSetting the Destination Timer Arrival Time Remaining Time DisplayDestination Timer Measuring Procedure Displaying Arrival Time Set during Measurement Remaining TimeTime up Elapsed Time DisplayAlarm on Alarm OFF Using the Alarm ModeAlarm ON/OFF and Alarm Monitor Setting the AlarmPage Using the Chronograph Mode Chronograph Timing ProcedureReading the Display Using the Timer Mode Setting the TimerTimer Setting Display Timer Measuring Procedure Setting display Timing Stop Time upRepeating Measurement Garbage Collection Using the System Monitor ModeCharge Level Indicator Charge Level Indicator Flash Memory Status DisplayFlash Memory Status Display Garbage Collection Operating ProcedurePage Locations Displayed by this Watch Locations Pre-registered in this WatchLocation IrWW During AIR diving File Error Warning Explanation of Warning FunctionsInsufficient Charge Warning Abnormal Depth Warning Abnormal Pressure Detection Error WarningWater Sensor Check Warning Ascent Rate WarningDecompression Diving Warning Decompression Diving ErrorPermanent Error Warning Exceed Maximum Depth WarningPO2 Limit Warning Permanent ErrorPO2 limit Error Oxygen Toxication Time ErrorDiving Terms Used by this Watch Decompression Stop Safety StopRepetitive Diving Decompression DivingMaximum Depth Max. Depth Minimum Water Temperature Min.w.tempDive Time TimeAIR Diving Using the Dive Plan ModeSwitching the Display Dive Condition Display Dive Plan Display Dive Alarm DisplayHigh-Altitude Setting Nitrox SettingDive Condition Marks Nitrox Setting and Oxygen Concentration SettingSwitching from Nitrox Setting to AIR Setting AIROxygen Concentration Setting StateNITROXCalling Up No-Decompression Limit Time Dive AlarmDepth Alarm Dive Time AlarmSetting the Dive Alarm Dive Alarm MonitorDepth No. of times Alarm sounds Dive time AIR diving Nitrox diving Calling Up Scuba Diving Log DataCalling Up Skin Diving Log Data Deleting Log Data Water Depth Measurement Display Skin diving Using the Dive ModeDisplay during AIR Setting Explanation of Display During Water Depth MeasurementDuring Decompression Diving Display during Nitrox Setting Decompression Stop Graph Safety Stop Graph and Decompression Stop GraphSafety Stop Graph Display Depth MeasurementNo. of Dives Per Day and Recording Log Data Water Temperature MeasurementEnding the Dive Mode Dive Time MeasurementUsing the Surface Mode Low power mode Temporary function Time Display Date DisplayNo Display Setting the Time and Date Data Communication Functions Infrared CommunicationCommunication Range Display Sequence in Infrared Communication Mode Infrared Communication Mode Operating ProcedureDiving Log and Profile Data Watch SettingsCommunication by USB Interface Data Communication with PCPreparations for Communication USB CommunicationVAttachment of Ferrite Core Sending and Receiving Data Data Communication Between WatchesReceiving Transmitting WatchWatch ProcedureAll Reset Formatting Flash Memory Operating Environment Accessory SoftwareWhen Registering Animated Images in an Album PrinterWeb Browser Installing CAPgm Watch Setting Software Page Startup and Ending Aqualand Graph Nx and CAPgm Startup of Aqualand Graph Nx and CAPgmEnding Aqualand Graph Nx and CAPgm Communication Unit Leg Removable USB Cable ConnectorUsing the Communication Unit Installing BatteriesAttaching and Removing the Watch Windows98 or Windows98 SE Installing the USB DriverPage Windows Me Confirm that your personal computer has started up normally Windows2000WindowsXP Page Problem Possible Cause Corrective Action Reference TroubleshootingUnable to Slow Sounds Examples of Use Indication Handling Precautions for the watchCleaning the Watch TemperaturesStatic Electricity Shocks Chemical Agents, Gases and MercuryStorage Watch SpecificationsCharger Communication Unit Sold Separately