Citizen D710/D716 instruction manual All Reset

Page 77

All Reset

The time, date and all other watch settings are returned to their initial (default) settings when the all reset procedure is performed. Perform this all reset procedure in the following cases.

•There is an error in the watch display

•When charging the watch after it has stopped completely as a result of being insufficiently charged

Even if the all reset procedure is performed, location settings (displayed locations, names of locations), diving logs, daily graphics and anniversary graphics that have been set by the user in the PC remain without being deleted. However, it should be noted that only diving data acquired prior to performing the all reset procedure on the day the all reset procedure is performed may be deleted.

Procedure

(1)Simultaneously press and then simultaneously release the lower right button (A), upper right button (B), upper left button (C) and lower left button (D).

•All of the display elements on the watch are displayed after an alarm sounds and "INITIALIZE" is displayed.

(2)Press any of the buttons once while all the display elements are displayed.

•The watch displays the time mode of the standard mode after "LOADING" is displayed.

(C)

(D)

(B)

(A)

This completes the all reset procedure. Correctly reset the time and date as well as other modes after performing the all reset procedure.

*When the All-Reset procedure is performed, <Current Log Counter in watch (Total number of Dives)> is reset to zero. If you want to continue counting from the previous log number, re-enter the previous log number for <Your Current Log Number> with the CAPgm software provided.

*Although an alarm sounds every second while all of the display elements of the watch are displayed, this is not a malfunction.

*If all of the display elements are not displayed after performing step (1) of the procedure (such as when the alarm continues to sound without the display changing), repeat step (1) of the procedure.

*The watch automatically returns to the time mode of the standard mode if none of the buttons are pressed for about 2 minutes while all of the display elements are displayed after performing step (1) of the procedure. The all reset procedure is completed in this case as well.

77

Image 77

Contents D710/ D716 Page English English English English Before UsingIntroduction Important Notes Safety Precautions Observe at All TimesGeneral Cautions Regarding Diving Page Page Page Contents Page Using the Scuba Diving Log Mode and Skin Diving Log Mode Watch Checking Accessories Prohibited Prohibited Use During Diving Page Page Various watch functions can be set on your PC FeaturesOther Convenient Functions This watch is of the rechargeable typeNames and Functions of Components ChargerPcs. of size AA Alkaline Batteries Installation Procedure Charging the Watch Watch Display During Charging Watch Display Modes Functions Standard ModeNames of Components Scuba Diving Log Mode Dive Plan ModeSkin Diving Log Mode Dive ModeHow to Read the Charge Level Indicator of the watch Charge Level Indicator and Continuous Usage TimeAmount of Charge Usage timeContinuous Usage Time UsingUsingthetheELELLightLightDive Plan Switching the ModeStandard Mode Page Using the Time Mode Using the Standard ModeSwitching the Display Day DisplaySetting the Time and Date Daily Graphic Display Normal Display Time Difference Display Using the Travel Time ModeSetting the Travel Time Before Interchanging ProcedureAfter interchanging During interchangingSetting the Destination Timer Using the Destination Timer ModeArrival Time Remaining Time Display DisplayDestination Timer Measuring Procedure Time up Remaining TimeElapsed Time Display Displaying Arrival Time Set during MeasurementAlarm ON/OFF and Alarm Monitor Using the Alarm ModeSetting the Alarm Alarm on Alarm OFFPage Reading the Display Using the Chronograph ModeChronograph Timing Procedure Timer Setting Display Using the Timer ModeSetting the Timer Repeating Measurement Timer Measuring ProcedureSetting display Timing Stop Time up Charge Level Indicator Using the System Monitor ModeCharge Level Indicator Flash Memory Status Display Garbage CollectionFlash Memory Status Display Garbage Collection Operating ProcedurePage Location IrWW Locations Displayed by this WatchLocations Pre-registered in this Watch During AIR diving Insufficient Charge Warning File Error WarningExplanation of Warning Functions Water Sensor Check Warning Abnormal Pressure Detection Error WarningAscent Rate Warning Abnormal Depth WarningPermanent Error Warning Decompression Diving ErrorExceed Maximum Depth Warning Decompression Diving WarningPO2 limit Error Permanent ErrorOxygen Toxication Time Error PO2 Limit WarningDiving Terms Used by this Watch Repetitive Diving Safety StopDecompression Diving Decompression StopDive Time Minimum Water Temperature Min.w.tempTime Maximum Depth Max. DepthSwitching the Display Using the Dive Plan ModeDive Condition Display Dive Plan Display Dive Alarm Display AIR DivingHigh-Altitude Setting Nitrox SettingSwitching from Nitrox Setting to AIR Setting Nitrox Setting and Oxygen Concentration SettingAIROxygen Concentration Setting StateNITROX Dive Condition MarksDepth Alarm Dive AlarmDive Time Alarm Calling Up No-Decompression Limit TimeDepth No. of times Alarm sounds Dive time Setting the Dive AlarmDive Alarm Monitor AIR diving Nitrox diving Calling Up Scuba Diving Log DataCalling Up Skin Diving Log Data Deleting Log Data Water Depth Measurement Display Skin diving Using the Dive ModeDuring Decompression Diving Display during AIR SettingExplanation of Display During Water Depth Measurement Display during Nitrox Setting Safety Stop Graph Display Safety Stop Graph and Decompression Stop GraphDepth Measurement Decompression Stop GraphEnding the Dive Mode Water Temperature MeasurementDive Time Measurement No. of Dives Per Day and Recording Log DataUsing the Surface Mode No Display Low power mode Temporary functionTime Display Date Display Setting the Time and Date Communication Range Data Communication FunctionsInfrared Communication Display Sequence in Infrared Communication Mode Infrared Communication Mode Operating ProcedureCommunication by USB Interface Watch SettingsData Communication with PC Diving Log and Profile DataVAttachment of Ferrite Core Preparations for CommunicationUSB Communication Sending and Receiving Data Data Communication Between WatchesReceiving Transmitting WatchWatch ProcedureAll Reset Formatting Flash Memory Operating Environment Accessory SoftwareWeb Browser When Registering Animated Images in an AlbumPrinter Installing CAPgm Watch Setting Software Page Ending Aqualand Graph Nx and CAPgm Startup and Ending Aqualand Graph Nx and CAPgmStartup of Aqualand Graph Nx and CAPgm Communication Unit Leg Removable USB Cable ConnectorAttaching and Removing the Watch Using the Communication UnitInstalling Batteries Windows98 or Windows98 SE Installing the USB DriverPage Windows Me Confirm that your personal computer has started up normally Windows2000WindowsXP Page Problem Possible Cause Corrective Action Reference TroubleshootingUnable to Slow Sounds Examples of Use Indication Handling Precautions for the watchStatic Electricity Cleaning the WatchTemperatures Storage ShocksChemical Agents, Gases and Mercury Watch SpecificationsCharger Communication Unit Sold Separately