Bushnell TRS-25 owner manual FCC Compliance Statement

Page 8

FCC Compliance Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

·Reorient or relocate the receiving antenna.

·Increase the separation between the equipment and receiver.

·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

·Consult the dealer or an experienced radio/TV technician for help.

The device does not contain any user-serviceable parts. Repairs should only be made by an Authorized Bushnell repair center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and will void your warranty and your authority to operate this device under Part 15 regulations.

The shielded interface cable which is provided must be used with the equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

Specifications and designs are subject to change without any notice or obligation on the part of the manufacturer.

8

Image 8
Contents Trophy Contents Pages Bar Battery CapBase Allen Wrench Shaft Setup and Operation Installing the BatteryInstalling the Sight on the Firearm Installing the Sight on a Picatinny/Weaver RailZeroing Operation Under Extreme ConditionsTrouble Shooting Possible Causes/SolutionsMaintenance Operation Under Extreme ConditionsTWO-YEAR Limited Warranty FCC Compliance Statement Français Assemblage ET Préparatifs Zérotage Utilisation EN Conditions ExtrêmesImpossible de zéroter Méthodes DE Recherche DE PanneLe point rouge n’apparaît pas Garantie Limitée de Deux ans Au CANADA, envoyez à Bushnell Outdoor Products Attn. RepairsPage Tamaño 3 mm Para la base Cierre Tapa de la bateríaCommutateur rotatif Base Llave Allen Eje Montaje Y Preparativos Para EL USO Puesta a cero Operación EN Condiciones ExtremasLocalización DE Fallos En EE UU, enviar a Bushnell Outdoor Products Attn. Repairs En CANADÁ, enviar a Bushnell Outdoor Products Attn. RepairsNota de la FCC Batteriedeckel Drehschalter Schiene Inbusschlüssel Schaft Größe 3 mmMontage des Visiers auf der Waffe Zusammenbau UND Vorbereitung ZUM GebrauchBatterieeinbau Staubschutzkappen Roter Leuchtpunkt Erscheint Nicht Zentrieren Nicht MöglichGewährleistungsfrist Zwei Jahre Anmerkung bezüglich FCC Richtlinien Cappuccio della manopola di regolazione dellelevazione Base Chiave a brugola 3 mm Tubo Barra diCoperchi di protezione delle lenti Installazione della batteriaInstallazione del dispositivo di puntamento sullarma Funzionamento in Condizioni Estreme AzzeramentoRicerca Guasti Possibili cause/soluzioniGaranzia Limitata PER DUE Anni Page Tampa da Bateria Base Chave de Allen 3 mm VeioInstalling the Sight on a Picatinny/Weaver Rail Como instalar a BateriaComo instalar a Mira na Arma Coberturas das LentesZeragem Funcionamento EM Condições ExtremasResolução DE Problemas Causas/Soluções PossíveisGarantia Limitada DE Dois Anos Nota da FCC Page Bushnell outdoor products