Sears 23949 user manual Wires Tip Avoid pinching the wires. Press

Page 11

11.	Apply grease to a Pedal Arm Axle (64).	11
		11
	Next, slide an M8 Washer (97) and an Axle
	Spacer (77) onto an M8 x 13mm Screw (82), and
	tighten the Screw a few turns into the Pedal Arm
	Axle (64).
	While a second person holds the front end of the
	Right Pedal Arm (58) inside the bracket on the
	Right Upper Body Leg (60), insert the Pedal Arm
	Axle (64) into both parts.
	Slide an M8 Washer (97) and an Axle Spacer	99	60
	(77) onto another M8 x 13mm Screw (82), and	82	Grease
	tighten the Screw a few turns into the Pedal Arm	97	64
	Axle (64). Then, tighten both Screws at the	97	64
	Axle (64). Then, tighten both Screws at the	77	77
	same time.		97	82
	Repeat this step on the other side of the		58	82
			58

	elliptical.
	See assembly step 4. Tighten the M10 x 25mm
	Screws (99).
12.	Orient the Shield Cover (75) assembly as shown.	12
		12
	While a second person holds the Shield Cover
	(75) assembly near the Upright (4), connect the		Avoid pinching
	Fan Extension Wire (146) to the Fan Wire (136).		Avoid pinching
			the wires

	Tip: Avoid pinching the wires. Press the
	Shield Cover (75) onto the Left and Right Shields	4
	(73, 74).	4
	(73, 74).

73, 74

146

136

75

11

Image 11

Contents Call TOLL-FREE QUESTIONS?Model No Serial No Table of Contents Important Precautions Before YOU Begin Part Identification Chart While you complete this step AssemblySon hold the Frame to prevent it from tipping Do not fully tighten the Screws yet Avoid pinching Wires and avoid Damaging the tabsRepeat these actions for the Left Upper Body Leg Tip To prevent the wires from falling intoUpright 4, secure the wires with the wire tie Center it. Tip It may be helpful to use a Rubber malletRepeat this step for the Left Upper Body Arm 101 Wires Tip Avoid pinching the wires. Press Page Repeat this step on the other side of the elliptical Page Chest Heart Rate Monitor HOW to PUT on the Heart Rate MonitorCare and Maintenance TroubleshootingHOW to Plug in the Power Cord HOW to USE the EllipticalHOW to Adjust the Positions of the Pedals HOW to Move the EllipticalVariety, you can turn the pedals in the opposite direction HOW to Exercise on the EllipticalHOW to Level the Elliptical Console Diagram Features of the Console Select the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Follow your progress with the display Turn on the fan if desired When you are finished exercising, unplug the power cordMeasure your heart rate if desired Begin pedaling to start the workout HOW to USE AN Onboard WorkoutSelect an onboard workout Set a calories, distance, or time goal HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit WorkoutMake sure that the iFit module is inserted in the console Select a user Select an iFit workoutHOW to USE the Sound System HOW to Change Console SettingsCheck the status of the iFit module if desired Set the default menu if desiredExit the information mode FCC InformationHOW to Calibrate the Ramp Maintenance and TroubleshootingConsole Troubleshooting Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Description Qty Part ListQty Description Drawing ExplodedDrawing Exploded Drawing Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty