Sears 23949 user manual Tip To prevent the wires from falling into, At the same time

Page 8

	5. See the inset drawing. Locate the wire tie in the	5
	lower end of the Upright (4). Tie the wire tie to	5	Wire Tie
	lower end of the Upright (4). Tie the wire tie to
	the Upper Wire (110) and to the Fan Extension
	the Upper Wire (110) and to the Fan Extension
	Wire (146). Then, pull the upper end of the wire		146
	tie until the Upper Wire and the Fan Extension		110
	Wire are routed through the Upright.		110
	Tip: To prevent the wires from falling into the	146
	Upright (4), secure the wires with the wire tie.	110
		Wire	4
		Tie
			146
			110
	6. Using a plastic bag to keep your fingers clean,	6
	apply some of the included grease to the Pivot	6
	apply some of the included grease to the Pivot
	Axle (35) and to two 16mm Wave Washers (54).
	Insert the Pivot Axle (35) through the Upright (4)
	and center it. Tip: It may be helpful to use a
	rubber mallet.	4
	Identify the Right Upper Body Leg (60) and	4
	Identify the Right Upper Body Leg (60) and	35	Grease
	orient it as shown.		54
	Slide a 16mm Wave Washer (54) and the Right		54
	Slide a 16mm Wave Washer (54) and the Right		60
	Upper Body Leg (60) onto the right side of the		97
	Pivot Axle (35).		82
	Repeat these actions for the Left Upper Body	46
	Leg (46).	46
	Leg (46).
	Tighten an M8 x 13mm Screw (82) and an M8
	Washer (97) into each end of the Pivot Axle (35)
	at the same time.
		8

Image 8

Contents Call TOLL-FREE QUESTIONS?Model No Serial No Table of Contents Important Precautions Before YOU Begin Part Identification Chart While you complete this step AssemblySon hold the Frame to prevent it from tipping Avoid pinching Wires and avoid Damaging the tabs Do not fully tighten the Screws yetTip To prevent the wires from falling into Upright 4, secure the wires with the wire tieCenter it. Tip It may be helpful to use a Rubber mallet Repeat these actions for the Left Upper Body LegRepeat this step for the Left Upper Body Arm 101 Wires Tip Avoid pinching the wires. Press Page Repeat this step on the other side of the elliptical Page HOW to PUT on the Heart Rate Monitor Care and MaintenanceTroubleshooting Chest Heart Rate MonitorHOW to USE the Elliptical HOW to Plug in the Power CordHOW to Move the Elliptical HOW to Adjust the Positions of the PedalsVariety, you can turn the pedals in the opposite direction HOW to Exercise on the EllipticalHOW to Level the Elliptical Console Diagram Features of the Console Select the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Follow your progress with the display Turn on the fan if desired When you are finished exercising, unplug the power cordMeasure your heart rate if desired Begin pedaling to start the workout HOW to USE AN Onboard WorkoutSelect an onboard workout HOW to USE a SET-A-GOAL Workout Set a calories, distance, or time goalHOW to USE AN Ifit Workout Make sure that the iFit module is inserted in the consoleSelect a user Select an iFit workout Start the workout. See onHOW to Change Console Settings HOW to USE the Sound SystemSet the default menu if desired Exit the information modeFCC Information Check the status of the iFit module if desiredHOW to Calibrate the Ramp Maintenance and TroubleshootingConsole Troubleshooting Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part List Description QtyQty Description Exploded DrawingDrawing Exploded Drawing Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty