JVC RX-E100SL manual Basic Settings, Setting the Digital Input, Terminals, Press Setting

Page 12

Basic Settings

CONTROL
5/°/3/2	Display
STANDBY
POWER	RX-E100 HOME THEATER RECEIVER

CONTROL

ANALOG

L

C

R

PRO LOGIC

SLEEP

TUNED

ST

AUTO

MUTING

LPCM

SUBWFR LFE DSP

MH

DOLBY D

LS

S

RS

DGTL AUTO

KH

INPUT

SURROUND

DSP

SETTING

ADJUST

MEMORY

DTS

INPUT ATT

VOL

ANALOG/DIGITAL

ON/OFF

MODE

MASTER VOLUME

INPUT ATT

D I G I T A L

DVD

TV

VCR

CD

FM

AM

S U R R O U N D

D I G I T A L

SETTING	Source selecting buttons	INPUT
	(DVD, TV, CD)	ANALOG/DIGITAL

Setting the Digital Input	Remote
Terminals	NOT

When you use the digital input terminals, register what components are connected to which terminals (DIGITAL IN 1/2) so that the correct source name will appear when you select the digital source.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

3Press CONTROL 3 (or 2) to select the appropriate digital terminal setting.

•Each time you press the button, the display changes to show the following:

	CONTROL
ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE			DSP
DOLBY D				DGTL AUTO
DTS	LS	S	RS	INPUT ATT	VOL

1Press SETTING.

SETTING	The CONTROL buttons now work for basic
	settings.

2Press CONTROL ° (or 5) repeatedly until “DGT (Digital)” (with the current setting) * appears on the display.

CONTROL

(back to the begining)

Note:

When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components.

•DIGITAL 1 (coaxial): For DVD player

•DIGITAL 2 (optical): For digital TV tuner

VOL

*“1DVD2TV” is the initial setting. If you have already changed the setting, another combination will be shown.

10

Image 12

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Getting StartedConnecting the FM and AM Antennas GettingStarted AM antenna connectionConnecting the Speakers Speaker Layout DiagramConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting Audio/Video Components Connecting the Power CordConnecting cords are not supplied with this unit. Use Digital connectionsDVD Turn On the Power To turn off the power into standbyTo increase the volume, press and hold To decrease the volume, press and holdTurning Off the Power With the TimerBasic Operations Basic Settings Setting the Digital InputPress Setting TerminalsBasic Settings Selecting the Analog or Digital Input ModeWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Setting the Subwoofer Information Setting the Speakers forDSP Modes Press Control 3or 2 to select YESDelay Time CTR DL, Rear DL Ex. When registering the rear speaker sizePress Control 3 or 2 to select the appropriate speaker size DisplayPress Control 3or 2 to select the delay time Repeat steps 2 and 3 to adjust the other delay timeEx. When adjusting the center delay Crossover Frequency CrossPress Control 3or 2 to select the LFE attenuator level Dynamic Range Compression D.R.CLow Frequency Effect Attenuator LFE Setting Auto Surround To cancel Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orSound Adjustments Basic Settings/Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerWhen using the remote control Reinforcing the BassPress Control 3 or 2 to turn on or OFF Bass Boost Sound Adjustments Adjusting the ToneAdjusting the Subwoofer Output Level Tuning in Stations Manually Using Preset TuningTuner Operations Press FM or AM to select the bandSelecting the FM Reception Mode To tune in a preset stationTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Available DSP modes according to the input signal format Creating Realistic Sound FieldsDAP Digital Acoustic Processor Modes Creating sound fieldSurround mode DSP modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Adjust the following speaker output levels from -10 to +10 Using Theater Surround Remote ControlPress Test to check the speaker output balance Press Test again to stop the test toneTo cancel Theater Surround Press Effect to select the DSP effect level 1 to You wantUsing DAP Modes Remote Control Adjust the rear speaker output levels from -10 to +10To cancel DAP Mode Using Surround Modes Front Panel Press Surround ON/OFF to activate anDigital, or DTS Digital Surround SeeUsing Theater Surround Front Panel Press Control 3or 2 to adjust the speaker output levelEx. When adjusting the center speaker output level Press Control 3or 2 to make an adjustment Repeat steps 4 and 5 to make other adjustmentsUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Mastering Remote Operations Operating other JVC products Audio/video operation buttonsRemote Control Parts IdentificationFront Panel Troubleshooting Parts Identification/TroubleshootingSpecifications AmplifierFM tuner IHF AM tunerMemorandum Source Name781 954 650 Valley Road Wayne, NJ1099 Limited Warranty AUDIO-2 0301NHMMDWJEIN