JVC RX-E100SL manual Dvd

Page 9

Illustrations of the input/output terminals below are typical examples.

When you connect other components, refer also to their manuals since the terminal names actually printed on the rear vary among the components.

Getting Started

A

B

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

DVD

TV

•When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components.

–DIGITAL 1 (coaxial): For DVD player

–DIGITAL 2 (optical): For digital TV tuner

If you connect other components, change the digital input (DIGITAL IN) terminal setting correctly. See “Setting the Digital Input Terminals” on page 10.

•Select the digital input mode correctly. See “Selecting the Analog or Digital Input Mode” on page 11.

C

AUDIO OUT		TV
AUDIO OUT
	LEFT
	RIGHT
AUDIO OUT
	LEFT	DVD
		DVD
	RIGHT
FRONT/MIX
LINE OUT
	LEFT	CD
		CD
	RIGHT
AUDIO
		LEFT
		RIGHT
OUT	IN	VCR
OUT	IN

•Connect the video input directly to the video output on the DVD player and/or VCR.

•You can also connect the digital TV tuner using the optical digital cable (see above).

•Connect the video out directly to the video input on the TV.

•To enjoy the software encoded with Dolby Digital or DTS Digital

Surround, connect the DVD player using one of the DIGITAL IN terminals (see above).

You can also connect the CD player using one of the DIGITAL IN terminals (see above).

Connect the video out directly to the video input on the TV.

7

Image 9

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Putting Batteries in the Remote Control Before InstallationChecking the Supplied Accessories Getting StartedGetting Connecting the FM and AM AntennasStarted AM antenna connectionSpeaker Layout Diagram Connecting the SpeakersConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting the Power Cord Connecting Audio/Video ComponentsConnecting cords are not supplied with this unit. Use Digital connectionsDVD To turn off the power into standby Turn On the PowerTo increase the volume, press and hold To decrease the volume, press and holdTurning Off the Power With the TimerBasic Operations Setting the Digital Input Basic SettingsPress Setting TerminalsBasic Settings Selecting the Analog or Digital Input ModeWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Setting the Speakers for Setting the Subwoofer InformationDSP Modes Press Control 3or 2 to select YESEx. When registering the rear speaker size Delay Time CTR DL, Rear DLPress Control 3 or 2 to select the appropriate speaker size DisplayRepeat steps 2 and 3 to adjust the other delay time Press Control 3or 2 to select the delay timeEx. When adjusting the center delay Crossover Frequency CrossPress Control 3or 2 to select the LFE attenuator level Dynamic Range Compression D.R.CLow Frequency Effect Attenuator LFE To cancel Auto Surround Setting Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orBasic Settings/Sound Adjustments Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerWhen using the remote control Reinforcing the BassPress Control 3 or 2 to turn on or OFF Bass Boost Sound Adjustments Adjusting the ToneAdjusting the Subwoofer Output Level Using Preset Tuning Tuning in Stations ManuallyTuner Operations Press FM or AM to select the bandTo tune in a preset station Selecting the FM Reception ModeTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Creating Realistic Sound Fields Available DSP modes according to the input signal formatDAP Digital Acoustic Processor Modes Creating sound fieldDSP mode Surround modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Using Theater Surround Remote Control Adjust the following speaker output levels from -10 to +10Press Test to check the speaker output balance Press Test again to stop the test tonePress Effect to select the DSP effect level 1 to You want To cancel Theater SurroundUsing DAP Modes Remote Control Adjust the rear speaker output levels from -10 to +10To cancel DAP Mode Press Surround ON/OFF to activate an Using Surround Modes Front PanelDigital, or DTS Digital Surround SeeUsing Theater Surround Front Panel Press Control 3or 2 to adjust the speaker output levelEx. When adjusting the center speaker output level Repeat steps 4 and 5 to make other adjustments Press Control 3or 2 to make an adjustmentUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Operating other JVC products Audio/video operation buttons Mastering Remote OperationsRemote Control Parts IdentificationFront Panel Parts Identification/Troubleshooting TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerSource Name Memorandum781 954 650 Valley Road Wayne, NJ1099 Limited Warranty AUDIO-2 0301NHMMDWJEIN