JVC RX-E100SL manual Press Control 3or 2 to select the LFE attenuator level

Page 17

Dynamic Range Compression — D.R.C.

You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night.

•This function takes effect only when playing back a source using Dolby Digital.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Low Frequency Effect Attenuator — LFE

If the bass sound is distorted while playing back software using Dolby Digital or DTS Digital Surround, follow the procedure below.

•This function takes effect only when the subwoofer (LFE) signals come in, (with “SUBWFR” set to “YES”).

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1Press SETTING.

Basic Settings

1Press SETTING.

The CONTROL buttons now work for basic

SETTING

settings.

SETTING

The CONTROL buttons now work for basic settings.

2Press CONTROL°(or 5) repeatedly until “D.R.C. (Dynamic Range Compression)” (with the current setting)* appears on the display.

CONTROL

IC

TO

T

VOL

*“MID” is the initial setting. If you have already changed the setting, another setting will be shown.

3Press CONTROL 3 (or 2) to select the appropriate compression level.

•Each time you press the button, the compression level changes as follows:

CONTROL
ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE			DSP
DOLBY D	LS	S	RS	DGTL AUTO	VOL
DTS	LS	S	RS	INPUT ATT	VOL

2Press CONTROL °(or 5) repeatedly until “LFE (Low Frequency Effect)” (with the current setting)* appears on the display.

CONTROL

C

O

VOL

*“0” is the initial setting. If you have already changed the setting, “–10dB” will be shown.

3Press CONTROL 3(or 2) to select the LFE attenuator level.

•Each time you press the button, the LFE attenuator level changes as follows:

CONTROL
ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE			DSP
DOLBY D	LS	S	RS	DGTL AUTO	VOL
DTS	LS	S	RS	INPUT ATT	VOL

OFF : Select this when you want to enjoy surround with its full dynamic range. (No effect applied.)

MID : Select this when you want to reduce the dynamic range a little.

MAX : Select this when you want to apply the compression effect fully. (Useful at night.)

0dB : Normally select this.

–10dB : Select this when the bass sound is distorted.

15

Image 17

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Putting Batteries in the Remote Control Before InstallationChecking the Supplied Accessories Getting StartedGetting Connecting the FM and AM AntennasStarted AM antenna connectionSpeaker Layout Diagram Connecting the SpeakersConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting the Power Cord Connecting Audio/Video ComponentsConnecting cords are not supplied with this unit. Use Digital connectionsDVD To turn off the power into standby Turn On the PowerTo increase the volume, press and hold To decrease the volume, press and holdBasic Operations Turning Off the PowerWith the Timer Setting the Digital Input Basic SettingsPress Setting TerminalsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Basic SettingsSelecting the Analog or Digital Input Mode Setting the Speakers for Setting the Subwoofer InformationDSP Modes Press Control 3or 2 to select YESEx. When registering the rear speaker size Delay Time CTR DL, Rear DLPress Control 3 or 2 to select the appropriate speaker size DisplayRepeat steps 2 and 3 to adjust the other delay time Press Control 3or 2 to select the delay timeEx. When adjusting the center delay Crossover Frequency CrossLow Frequency Effect Attenuator LFE Press Control 3or 2 to select the LFE attenuator levelDynamic Range Compression D.R.C To cancel Auto Surround Setting Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orBasic Settings/Sound Adjustments Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerPress Control 3 or 2 to turn on or OFF Bass Boost When using the remote controlReinforcing the Bass Adjusting the Subwoofer Output Level Sound AdjustmentsAdjusting the Tone Using Preset Tuning Tuning in Stations ManuallyTuner Operations Press FM or AM to select the bandTo tune in a preset station Selecting the FM Reception ModeTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Creating Realistic Sound Fields Available DSP modes according to the input signal formatDAP Digital Acoustic Processor Modes Creating sound fieldDSP mode Surround modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Using Theater Surround Remote Control Adjust the following speaker output levels from -10 to +10Press Test to check the speaker output balance Press Test again to stop the test tonePress Effect to select the DSP effect level 1 to You want To cancel Theater SurroundTo cancel DAP Mode Using DAP Modes Remote ControlAdjust the rear speaker output levels from -10 to +10 Press Surround ON/OFF to activate an Using Surround Modes Front PanelDigital, or DTS Digital Surround SeeEx. When adjusting the center speaker output level Using Theater Surround Front PanelPress Control 3or 2 to adjust the speaker output level Repeat steps 4 and 5 to make other adjustments Press Control 3or 2 to make an adjustmentUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Operating other JVC products Audio/video operation buttons Mastering Remote OperationsFront Panel Remote ControlParts Identification Parts Identification/Troubleshooting TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerSource Name Memorandum1099 781 954 650Valley Road Wayne, NJ Limited Warranty AUDIO-2 0301NHMMDWJEIN