JVC RX-E100SL manual Getting, Started, Connecting the FM and AM Antennas, AM antenna connection

Page 5

Connecting the FM and AM Antennas

Getting

AM Loop Antenna (supplied)

Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna.

If AM reception is poor, connect single vinyl-covered wire (not supplied).

If FM reception is poor, connect outdoor FM antenna (not supplied).

B

FM	75		L
		IA
AX
CO

75

FMCOAXIAL

AM LOOP

FM Antenna (supplied)

AM			FM 75
EXT			COAXIAL
	ANTENNA

Started

1

2

3

Notes:

•If the AM loop antenna wire is covered with vinyl, remove the vinyl while twisting it as shown to the right.

•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

		IN	1	SPEAKERS		:
	DIGITAL	IN	1	LEFT	+	CAUTION
	DIGITAL	DIGITALV		RIGHT	+	CAUTION
		(D	)	FRONT		SPEAKER
			SPEAKERS			IMPEDANCE6
			SPEAKERS			1
		REAR	LEFT	+	–	8
2	CENTER	RIGHT	+
DIGITALV)	CENTER	RIGHT	+
DIGITALV)	SPEAKER
(T	SPEAKER			–
			–	–
			–
	+
	–
SUBWOOFEROUT

							AUDIO
AM	LO	OP	75
AM			75
			FM
			COAXIAL	LEFT			DVD
		ANTENNA					TV
		ANTENNA				IN	CD
AM				RIGHT		(PLAY)	CD
AM				RIGHT	OUT	(PLAY)
EXT					OUT
EXT					(REC)
					VCR

AM antenna connection

Connect the AM loop antenna supplied to the AM LOOP terminals.

Turn the loop until you have the best reception.

•If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM loop antenna connected.)

FM antenna connection

Connect the FM antenna supplied to the FM 75 Ω COAXIAL terminal as temporary measure.

Extend the supplied FM antenna horizontally.

•If reception is poor, connect an outdoor antenna. Before attaching a 75 Ω coaxial cable (with a standard type connector),

disconnect the supplied FM antenna.

3

Image 5

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Putting Batteries in the Remote Control Before InstallationChecking the Supplied Accessories Getting StartedGetting Connecting the FM and AM AntennasStarted AM antenna connectionSpeaker Layout Diagram Connecting the SpeakersConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting the Power Cord Connecting Audio/Video ComponentsConnecting cords are not supplied with this unit. Use Digital connectionsDVD To turn off the power into standby Turn On the PowerTo increase the volume, press and hold To decrease the volume, press and holdBasic Operations Turning Off the PowerWith the Timer Setting the Digital Input Basic SettingsPress Setting TerminalsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Basic SettingsSelecting the Analog or Digital Input Mode Setting the Speakers for Setting the Subwoofer InformationDSP Modes Press Control 3or 2 to select YESEx. When registering the rear speaker size Delay Time CTR DL, Rear DLPress Control 3 or 2 to select the appropriate speaker size DisplayRepeat steps 2 and 3 to adjust the other delay time Press Control 3or 2 to select the delay timeEx. When adjusting the center delay Crossover Frequency CrossLow Frequency Effect Attenuator LFE Press Control 3or 2 to select the LFE attenuator levelDynamic Range Compression D.R.C To cancel Auto Surround Setting Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orBasic Settings/Sound Adjustments Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerPress Control 3 or 2 to turn on or OFF Bass Boost When using the remote controlReinforcing the Bass Adjusting the Subwoofer Output Level Sound AdjustmentsAdjusting the Tone Using Preset Tuning Tuning in Stations ManuallyTuner Operations Press FM or AM to select the bandTo tune in a preset station Selecting the FM Reception ModeTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Creating Realistic Sound Fields Available DSP modes according to the input signal formatDAP Digital Acoustic Processor Modes Creating sound fieldDSP mode Surround modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Using Theater Surround Remote Control Adjust the following speaker output levels from -10 to +10Press Test to check the speaker output balance Press Test again to stop the test tonePress Effect to select the DSP effect level 1 to You want To cancel Theater SurroundTo cancel DAP Mode Using DAP Modes Remote ControlAdjust the rear speaker output levels from -10 to +10 Press Surround ON/OFF to activate an Using Surround Modes Front PanelDigital, or DTS Digital Surround SeeEx. When adjusting the center speaker output level Using Theater Surround Front PanelPress Control 3or 2 to adjust the speaker output level Repeat steps 4 and 5 to make other adjustments Press Control 3or 2 to make an adjustmentUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Operating other JVC products Audio/video operation buttons Mastering Remote OperationsFront Panel Remote ControlParts Identification Parts Identification/Troubleshooting TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerSource Name Memorandum1099 781 954 650Valley Road Wayne, NJ Limited Warranty AUDIO-2 0301NHMMDWJEIN