JVC RX-E100SL manual Sound Adjustments, Adjusting the Tone, Adjusting the Subwoofer Output Level

Page 21

Adjusting the Tone	Remote
	NOT

You can adjust the bass and treble sounds as you like.

• You have to make these adjustments for each source.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1Press ADJUST.

ADJUSTThe CONTROL buttons now work for sound adjustments.

2Press CONTROL °(or 5) repeatedly until “BASS” or “TREBLE” (with the current setting)* appears.

CONTROL

Adjusting the Subwoofer Output Level

You can adjust the subwoofer output level if you have connected a subwoofer and set the subwoofer information correctly – “YES.”

• You have to make this adjustment for each source.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1Press ADJUST.

ADJUSTThe CONTROL buttons now work for sound adjustments.

2Press CONTROL ° (or 5) repeatedly until “SUBWFR (subwoofer)” (with the current

setting)* appears.

CONTROL

Sound Adjustments

ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE DSP					OGIC
DOLBY D	LS	S	RS	DGTL AUTO	VOL
DTS	LS	S	RS	INPUT ATT	VOL	AUTO

ATT VOL

					* “0” is the initial setting. If you have already changed the

					setting, another number (level) will be shown.
					3 Press CONTROL 3or 2to adjust the sound
BASS : To adjust the bass.					3 Press CONTROL 3or 2to adjust the sound

TREBLE : To adjust the treble.

*“0” is the initial setting. If you have already changed the setting, another number (level) will be shown.

3Press CONTROL 3 or 2to adjust the sound level.

CONTROL

ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE DSP
DOLBY D	LS	S	RS	DGTL AUTO	VOL
DTS	LS	S	RS	INPUT ATT	VOL

Ex.: When adjusting the bass level

•Pressing CONTROL 3increases the sound level by +2 steps (from –10 to +10).

•Pressing CONTROL 2decreases the sound level by –2 steps (from +10 to –10).

output level.

CONTROL

ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE DSP
DOLBY D	LS	S	RS	DGTL AUTO	VOL
DTS	LS	S	RS	INPUT ATT	VOL

•Pressing CONTROL 3increases the sound output level (from –10 to +10).

•Pressing CONTROL 2decreases the sound output level (from +10 to –10).

When using the remote control

1Press SOUND.

10 keys now work for sound adjustments.

2Press SUBWOOFER +/– to adjust the sound output level (from –10 to +10).

4Repeat steps 2 and 3 to adjust the other sound level.

19

Image 21

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Putting Batteries in the Remote Control Before InstallationChecking the Supplied Accessories Getting StartedGetting Connecting the FM and AM AntennasStarted AM antenna connectionSpeaker Layout Diagram Connecting the SpeakersConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting the Power Cord Connecting Audio/Video ComponentsConnecting cords are not supplied with this unit. Use Digital connectionsDVD To turn off the power into standby Turn On the PowerTo increase the volume, press and hold To decrease the volume, press and holdTurning Off the Power With the TimerBasic Operations Setting the Digital Input Basic SettingsPress Setting TerminalsBasic Settings Selecting the Analog or Digital Input ModeWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Setting the Speakers for Setting the Subwoofer InformationDSP Modes Press Control 3or 2 to select YESEx. When registering the rear speaker size Delay Time CTR DL, Rear DLPress Control 3 or 2 to select the appropriate speaker size DisplayRepeat steps 2 and 3 to adjust the other delay time Press Control 3or 2 to select the delay timeEx. When adjusting the center delay Crossover Frequency CrossPress Control 3or 2 to select the LFE attenuator level Dynamic Range Compression D.R.CLow Frequency Effect Attenuator LFE To cancel Auto Surround Setting Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orBasic Settings/Sound Adjustments Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerWhen using the remote control Reinforcing the BassPress Control 3 or 2 to turn on or OFF Bass Boost Sound Adjustments Adjusting the ToneAdjusting the Subwoofer Output Level Using Preset Tuning Tuning in Stations ManuallyTuner Operations Press FM or AM to select the bandTo tune in a preset station Selecting the FM Reception ModeTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Creating Realistic Sound Fields Available DSP modes according to the input signal formatDAP Digital Acoustic Processor Modes Creating sound fieldDSP mode Surround modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Using Theater Surround Remote Control Adjust the following speaker output levels from -10 to +10Press Test to check the speaker output balance Press Test again to stop the test tonePress Effect to select the DSP effect level 1 to You want To cancel Theater SurroundUsing DAP Modes Remote Control Adjust the rear speaker output levels from -10 to +10To cancel DAP Mode Press Surround ON/OFF to activate an Using Surround Modes Front PanelDigital, or DTS Digital Surround SeeUsing Theater Surround Front Panel Press Control 3or 2 to adjust the speaker output levelEx. When adjusting the center speaker output level Repeat steps 4 and 5 to make other adjustments Press Control 3or 2 to make an adjustmentUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Operating other JVC products Audio/video operation buttons Mastering Remote OperationsRemote Control Parts IdentificationFront Panel Parts Identification/Troubleshooting TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerSource Name Memorandum781 954 650 Valley Road Wayne, NJ1099 Limited Warranty AUDIO-2 0301NHMMDWJEIN