JVC RX-E100SL Connecting Audio/Video Components, Connecting the Power Cord, Digital connections

Page 8

Getting Started

Connecting Audio/Video Components

Connecting cords are not supplied with this unit. Use the		Turn the power off to all components before connections.
cords supplied for the other components or purchase them at
an audio or electric appliance store.
A	Optical digital cord	Digital connections
		DIGITAL IN
B		DIGITAL 2	DIGITAL 1
B	Coaxial digital cord	(TV)	(DVD)

C	Audio cord	Before connecting an
		optical digital cord, unplug

the protective plug.

RX-E100SL

SPEAKERS

Analog

IN

1

:

connections

LEFT

+

SPEAKER

DIGITAL

(D

RIGHT

DIGITALV

CAUTION

)

FRONT

SPEAKERS

IMPEDANCE6

1

REAR

LEFT

+

–

8

2

CENTER

RIGHT

+

DIGITALV)

(T

SPEAKER

–

–

+

AUDIO

–

SUBWOOFEROUT

LEFT

AUDIO

AM

LOOP

FM

RIGHT

75

COAXIAL

LEFT

DVD

ANTENNA

TV

OUT

AM

RIGHT

IN

CD

IN

(PLAY)

EXT

OUT

(REC)

(PLAY)

(REC)VCR

VCR

CD

TV

DVD

If you connect a sound-enhancing device such as a

graphic equalizer between the source components and

this receiver, the sound output through this receiver may

be distorted.

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all

connections have been made.

Plug the power cord into an AC outlet.

6

Image 8

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Getting StartedConnecting the FM and AM Antennas GettingStarted AM antenna connectionConnecting the Speakers Speaker Layout DiagramConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting Audio/Video Components Connecting the Power CordConnecting cords are not supplied with this unit. Use Digital connectionsDVD Turn On the Power To turn off the power into standbyTo increase the volume, press and hold To decrease the volume, press and holdBasic Operations Turning Off the PowerWith the Timer Basic Settings Setting the Digital InputPress Setting TerminalsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Basic SettingsSelecting the Analog or Digital Input Mode Setting the Subwoofer Information Setting the Speakers forDSP Modes Press Control 3or 2 to select YESDelay Time CTR DL, Rear DL Ex. When registering the rear speaker sizePress Control 3 or 2 to select the appropriate speaker size DisplayPress Control 3or 2 to select the delay time Repeat steps 2 and 3 to adjust the other delay timeEx. When adjusting the center delay Crossover Frequency CrossLow Frequency Effect Attenuator LFE Press Control 3or 2 to select the LFE attenuator levelDynamic Range Compression D.R.C Setting Auto Surround To cancel Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orSound Adjustments Basic Settings/Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerPress Control 3 or 2 to turn on or OFF Bass Boost When using the remote controlReinforcing the Bass Adjusting the Subwoofer Output Level Sound AdjustmentsAdjusting the Tone Tuning in Stations Manually Using Preset TuningTuner Operations Press FM or AM to select the bandSelecting the FM Reception Mode To tune in a preset stationTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Available DSP modes according to the input signal format Creating Realistic Sound FieldsDAP Digital Acoustic Processor Modes Creating sound fieldSurround mode DSP modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Adjust the following speaker output levels from -10 to +10 Using Theater Surround Remote ControlPress Test to check the speaker output balance Press Test again to stop the test toneTo cancel Theater Surround Press Effect to select the DSP effect level 1 to You wantTo cancel DAP Mode Using DAP Modes Remote ControlAdjust the rear speaker output levels from -10 to +10 Using Surround Modes Front Panel Press Surround ON/OFF to activate anDigital, or DTS Digital Surround SeeEx. When adjusting the center speaker output level Using Theater Surround Front PanelPress Control 3or 2 to adjust the speaker output level Press Control 3or 2 to make an adjustment Repeat steps 4 and 5 to make other adjustmentsUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Mastering Remote Operations Operating other JVC products Audio/video operation buttonsFront Panel Remote ControlParts Identification Troubleshooting Parts Identification/TroubleshootingSpecifications AmplifierFM tuner IHF AM tunerMemorandum Source Name1099 781 954 650Valley Road Wayne, NJ Limited Warranty AUDIO-2 0301NHMMDWJEIN