JVC RX-E100SL Basic Settings/Sound Adjustments, Attenuating the Input Signal, Output Balance

Page 19

Sound Adjustments

You can also use the remote control for some sound adjustments.

• When using the remote control, see also “Mastering Remote Operations” on page 32.

CONTROL
5/°/3/2	Display	INPUT ATT
STANDBY
POWER	RX-E100 HOME THEATER RECEIVER

CONTROL

ANALOG

L

C

R

PRO LOGIC

SLEEP

TUNED

ST

AUTO

MUTING

LPCM

SUBWFR LFE DSP

MH

DOLBY D

LS

S

RS

DGTL AUTO

KH

INPUT

SURROUND

DSP

SETTING

ADJUST

MEMORY

DTS

INPUT ATT

VOL

ANALOG/DIGITAL

ON/OFF

MODE

MASTER VOLUME

INPUT ATT

D I G I T A L

DVD

TV

VCR

CD

FM

AM

S U R R O U N D D I G I T A L

ADJUST

	Attenuating the Input Signal	Remote	2 Press CONTROL ° (or 5) repeatedly until
		NOT

	When the input level of the analog source is too high, the sounds		“BAL (Balance)” (with the current setting) *
			appears on the display.
	will be distorted. If this happens, you need to attenuate the input
			CONTROL
	signal level to prevent the sound distortion.

	• You have to make this adjustment for each analog source.		IC

TO

T

VOL

Press and hold INPUT ATT (INPUT ANALOG/DIGITAL) so

Basic Settings/Sound Adjustments

that the INPUT ATT indicator lights up on the display.

•Each time you press and hold the button, the Input Attenuator turns on (“ATT ON”) or off (“ATT NORMAL”).

INPUT

ANALOG/DIGITAL

INPUT ATT

ANALOG L			R

INPUT ATT

*“CENTER” is the initial setting. If you have already changed the setting, another setting will be shown.

3Press CONTROL 3or 2to adjust the front

speaker balance.

CONTROL
MUTI
MHZ
KHZ
VOL
ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE DSP
DOLBY D	LS	S	RS	DGTL AUTO	VOL
DTS	LS	S	RS	INPUT ATT	VOL

ATT ON

ATT NORMAL

Adjusting the Front Speaker	Remote
Output Balance	NOT

If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.

• You have to make this adjustment for each source.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•Pressing CONTROL 3decreases the left channel output (from CENTER to L–21).

•Pressing CONTROL 2decreases the right

channel output (from CENTER to R–21).

1Press ADJUST.

ADJUST	The CONTROL buttons now work for sound
	adjustments.

17

Image 19

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Getting Started Before InstallationPutting Batteries in the Remote Control Checking the Supplied AccessoriesAM antenna connection Connecting the FM and AM AntennasGetting StartedConnecting the subwoofer Connecting the SpeakersSpeaker Layout Diagram Connecting the front, center, and rear speakersLeft front speaker Digital connections Connecting Audio/Video ComponentsConnecting the Power Cord Connecting cords are not supplied with this unit. UseDVD To decrease the volume, press and hold Turn On the PowerTo turn off the power into standby To increase the volume, press and holdWith the Timer Turning Off the PowerBasic Operations Terminals Basic SettingsSetting the Digital Input Press SettingSelecting the Analog or Digital Input Mode Basic SettingsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Press Control 3or 2 to select YES Setting the Subwoofer InformationSetting the Speakers for DSP ModesDisplay Delay Time CTR DL, Rear DLEx. When registering the rear speaker size Press Control 3 or 2 to select the appropriate speaker sizeCrossover Frequency Cross Press Control 3or 2 to select the delay timeRepeat steps 2 and 3 to adjust the other delay time Ex. When adjusting the center delayDynamic Range Compression D.R.C Press Control 3or 2 to select the LFE attenuator levelLow Frequency Effect Attenuator LFE Each time you press the button, Auto Surround turns on or Setting Auto SurroundTo cancel Auto Surround To activate Auto Surround, follow the procedure belowAdjusting the Front Speaker Sound AdjustmentsBasic Settings/Sound Adjustments Attenuating the Input SignalReinforcing the Bass When using the remote controlPress Control 3 or 2 to turn on or OFF Bass Boost Adjusting the Tone Sound AdjustmentsAdjusting the Subwoofer Output Level Press FM or AM to select the band Tuning in Stations ManuallyUsing Preset Tuning Tuner OperationsTuner Operations Selecting the FM Reception ModeTo tune in a preset station To restore the stereo effectCreating Realistic Sound Fields Creating sound field Available DSP modes according to the input signal formatCreating Realistic Sound Fields DAP Digital Acoustic Processor ModesAbout Relations between Speaker Layout and DSP Modes Surround modeDSP mode When Auto SR Auto Surround is turned onUsing Surround Modes Remote Control Press Test again to stop the test tone Adjust the following speaker output levels from -10 to +10Using Theater Surround Remote Control Press Test to check the speaker output balancePress Effect to select the DSP effect level 1 to You want To cancel Theater SurroundAdjust the rear speaker output levels from -10 to +10 Using DAP Modes Remote ControlTo cancel DAP Mode See Using Surround Modes Front PanelPress Surround ON/OFF to activate an Digital, or DTS Digital SurroundPress Control 3or 2 to adjust the speaker output level Using Theater Surround Front PanelEx. When adjusting the center speaker output level Ex. When adjusting the left rear speaker output level Press Control 3or 2 to make an adjustmentRepeat steps 4 and 5 to make other adjustments Using DAP Modes Front PanelMastering Remote Operations Operating other JVC products Audio/video operation buttons Mastering Remote OperationsParts Identification Remote ControlFront Panel Parts Identification/Troubleshooting TroubleshootingAM tuner SpecificationsAmplifier FM tuner IHFSource Name MemorandumValley Road Wayne, NJ 781 954 6501099 Limited Warranty AUDIO-2 0301NHMMDWJEIN