JVC RX-E100SL Press Control 3or 2 to select the delay time, Crossover Frequency Cross, Display

Page 16

Basic Settings

CONTROL

5/°/3/2 Display

STANDBY
POWER	RX-E100	HOME THEATER RECEIVER

CONTROL

ANALOG

L

C

R

PRO LOGIC

SLEEP

TUNED

ST

AUTO

MUTING

LPCM

SUBWFR LFE DSP

MH

DOLBY D

LS

S

RS

DGTL AUTO

KH

INPUT

SURROUND

DSP

SETTING

ADJUST

MEMORY

DTS

INPUT ATT

VOL

ANALOG/DIGITAL

ON/OFF

MODE

MASTER VOLUME

INPUT ATT

D I G I T A L

DVD

TV

VCR

CD

FM

AM

S U R R O U N D D I G I T A L

SETTING

3Press CONTROL 3(or 2) to select the delay time.

•Each time you press the button, the delay time changes by “1 mS (msec).”

CONTROL

2Press CONTROL ° (or 5) repeatedly until “CROSS (Crossover)” (with the current setting) * appears on the display.

CONTROL

	ANALOG	L	C	R PRO LOGIC
	LPCM	SUBWFR LFE DSP
	DOLBY D	LS	S	RS	DGTL AUTO
	DTS				INPUT ATT

GIC

UTO
TT	VOL

VOL

Ex.: When adjusting the center delay

4Repeat steps 2 and 3 to adjust the other delay time.

Crossover Frequency — CROSS

Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this receiver automatically reallocates the bass sound elements assigned to the small speaker to large speakers.

To use this function properly, set this crossover frequency level according to the size of the small speaker connected.

•If you have selected “LRG (large)” for all speakers, this function will not take effect.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1Press SETTING.

*“100HZ” is the initial setting. If you have already changed the setting, another frequency will be shown.

3Press CONTROL 3 (or 2) to select the crossover frequency level.

•Each time you press the button, the crossover frequency level changes as follows:

CONTROL
ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE			DSP
DOLBY D	LS	S	RS	DGTL AUTO	VOL
DTS	LS	S	RS	INPUT ATT	VOL

• Use the following criteria as reference when adjusting:

80HZ: Select this frequency when the cone speaker unit built in the speaker is about 4 3/4 inches (12 cm).

100HZ: Select this frequency when the cone speaker unit built in the speaker is about 3 15/16 inches (10 cm).

SETTING

The CONTROL buttons now work for basic settings.

120HZ: Select this frequency when the cone speaker unit built in the speaker is about 3 3/16 inches (8 cm).

14

Image 16

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Getting StartedConnecting the FM and AM Antennas GettingStarted AM antenna connectionConnecting the Speakers Speaker Layout DiagramConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting Audio/Video Components Connecting the Power CordConnecting cords are not supplied with this unit. Use Digital connectionsDVD Turn On the Power To turn off the power into standbyTo increase the volume, press and hold To decrease the volume, press and holdWith the Timer Turning Off the PowerBasic Operations Basic Settings Setting the Digital InputPress Setting TerminalsSelecting the Analog or Digital Input Mode Basic SettingsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Setting the Subwoofer Information Setting the Speakers forDSP Modes Press Control 3or 2 to select YESDelay Time CTR DL, Rear DL Ex. When registering the rear speaker sizePress Control 3 or 2 to select the appropriate speaker size DisplayPress Control 3or 2 to select the delay time Repeat steps 2 and 3 to adjust the other delay timeEx. When adjusting the center delay Crossover Frequency CrossDynamic Range Compression D.R.C Press Control 3or 2 to select the LFE attenuator levelLow Frequency Effect Attenuator LFE Setting Auto Surround To cancel Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orSound Adjustments Basic Settings/Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerReinforcing the Bass When using the remote controlPress Control 3 or 2 to turn on or OFF Bass Boost Adjusting the Tone Sound AdjustmentsAdjusting the Subwoofer Output Level Tuning in Stations Manually Using Preset TuningTuner Operations Press FM or AM to select the bandSelecting the FM Reception Mode To tune in a preset stationTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Available DSP modes according to the input signal format Creating Realistic Sound FieldsDAP Digital Acoustic Processor Modes Creating sound fieldSurround mode DSP modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Adjust the following speaker output levels from -10 to +10 Using Theater Surround Remote ControlPress Test to check the speaker output balance Press Test again to stop the test toneTo cancel Theater Surround Press Effect to select the DSP effect level 1 to You wantAdjust the rear speaker output levels from -10 to +10 Using DAP Modes Remote ControlTo cancel DAP Mode Using Surround Modes Front Panel Press Surround ON/OFF to activate anDigital, or DTS Digital Surround SeePress Control 3or 2 to adjust the speaker output level Using Theater Surround Front PanelEx. When adjusting the center speaker output level Press Control 3or 2 to make an adjustment Repeat steps 4 and 5 to make other adjustmentsUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Mastering Remote Operations Operating other JVC products Audio/video operation buttonsParts Identification Remote ControlFront Panel Troubleshooting Parts Identification/TroubleshootingSpecifications AmplifierFM tuner IHF AM tunerMemorandum Source NameValley Road Wayne, NJ 781 954 6501099 Limited Warranty AUDIO-2 0301NHMMDWJEIN