JVC RX-E100SL manual Reinforcing the Bass, Press Control 3 or 2 to turn on or OFF Bass Boost

Page 20

Sound Adjustments

CONTROL
5/°/3/2	Display	INPUT ATT
STANDBY
POWER	RX-E100 HOME THEATER RECEIVER

CONTROL

ANALOG

L

C

R

PRO LOGIC

SLEEP

TUNED

ST

AUTO

MUTING

LPCM

SUBWFR LFE DSP

MH

DOLBY D

LS

S

RS

DGTL AUTO

KH

INPUT

SURROUND

DSP

SETTING

ADJUST

MEMORY

DTS

INPUT ATT

VOL

ANALOG/DIGITAL

ON/OFF

MODE

MASTER VOLUME

INPUT ATT

D I G I T A L

DVD

TV

VCR

CD

FM

AM

S U R R O U N D D I G I T A L

ADJUST

Reinforcing the Bass

You can boost the bass level — Bass Boost.

• You have to make this adjustment for each source.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1Press ADJUST.

ADJUST	The CONTROL buttons now work for sound
	adjustments.

2Press CONTROL ° (or 5) repeatedly until “B. BOOST (Bass Boost)” (with the current setting) * appears on the display.

CONTROL

C

TO

T

VOL

*“OFF” is the initial setting. If you have already changed the setting, “ON” will be shown.

3Press CONTROL 3 (or 2) to turn “ON” or “OFF” Bass Boost.

CONTROL
ANALOG	L	C	R	PRO LOGIC
LPCM	SUBWFR LFE			DSP
DOLBY D	LS	S	RS	DGTL AUTO	VOL
DTS	LS	S	RS	INPUT ATT	VOL

ON : Select this to boost the bass level. (Bass Boost)

OFF : Select this to deactivate Bass Boost.

Note:

This function affects the sound outputting only through the front

speakers.

When using the remote control

1Press SOUND.

10 keys now work for sound adjustments.

2Press BASS BOOST.

•Each time you press the button, Bass Boost turns on and off alternately.

18

Image 20

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Getting StartedConnecting the FM and AM Antennas GettingStarted AM antenna connectionConnecting the Speakers Speaker Layout DiagramConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting Audio/Video Components Connecting the Power CordConnecting cords are not supplied with this unit. Use Digital connectionsDVD Turn On the Power To turn off the power into standbyTo increase the volume, press and hold To decrease the volume, press and holdBasic Operations Turning Off the PowerWith the Timer Basic Settings Setting the Digital InputPress Setting TerminalsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Basic SettingsSelecting the Analog or Digital Input Mode Setting the Subwoofer Information Setting the Speakers forDSP Modes Press Control 3or 2 to select YESDelay Time CTR DL, Rear DL Ex. When registering the rear speaker sizePress Control 3 or 2 to select the appropriate speaker size DisplayPress Control 3or 2 to select the delay time Repeat steps 2 and 3 to adjust the other delay timeEx. When adjusting the center delay Crossover Frequency CrossLow Frequency Effect Attenuator LFE Press Control 3or 2 to select the LFE attenuator levelDynamic Range Compression D.R.C Setting Auto Surround To cancel Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orSound Adjustments Basic Settings/Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerPress Control 3 or 2 to turn on or OFF Bass Boost When using the remote controlReinforcing the Bass Adjusting the Subwoofer Output Level Sound AdjustmentsAdjusting the Tone Tuning in Stations Manually Using Preset TuningTuner Operations Press FM or AM to select the bandSelecting the FM Reception Mode To tune in a preset stationTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Available DSP modes according to the input signal format Creating Realistic Sound FieldsDAP Digital Acoustic Processor Modes Creating sound fieldSurround mode DSP modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Adjust the following speaker output levels from -10 to +10 Using Theater Surround Remote ControlPress Test to check the speaker output balance Press Test again to stop the test toneTo cancel Theater Surround Press Effect to select the DSP effect level 1 to You wantTo cancel DAP Mode Using DAP Modes Remote ControlAdjust the rear speaker output levels from -10 to +10 Using Surround Modes Front Panel Press Surround ON/OFF to activate anDigital, or DTS Digital Surround SeeEx. When adjusting the center speaker output level Using Theater Surround Front PanelPress Control 3or 2 to adjust the speaker output level Press Control 3or 2 to make an adjustment Repeat steps 4 and 5 to make other adjustmentsUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Mastering Remote Operations Operating other JVC products Audio/video operation buttonsFront Panel Remote ControlParts Identification Troubleshooting Parts Identification/TroubleshootingSpecifications AmplifierFM tuner IHF AM tunerMemorandum Source Name1099 781 954 650Valley Road Wayne, NJ Limited Warranty AUDIO-2 0301NHMMDWJEIN