JVC RX-E100SL manual Specifications, Amplifier, FM tuner IHF, AM tuner, General

Page 38

Specifications

Designs & specifications are subject to change without notice.

Amplifier

Output Power

Audio Input Sensitivity/Impedance (1 kHz): Audio Input (DIGITAL IN)* :

Audio Output Level: Signal-to-Noise Ratio (’66 IHF/’78 IHF):

Frequency Response (8 Ω):

Tone Control:

Bass Boost:

FM tuner (IHF)

Tuning Range:

Usable Sensitivity:

50 dB Quieting Sensitivity:

Signal-to-Noise Ratio (IHF-A weighted):

Total Harmonic Distortion:

Stereo Separation at REC OUT:

Alternate Channel Selectivity:

Frequency Response:

AM tuner

Tuning Range:

Usable Sensitivity:

Signal-to-Noise Ratio:

General

Power Requirements:

Power Consumption:

Dimensions (W x H x D):

Mass:

At Stereo operation:

Front channels: 70 W per channel, min. RMS, driven into 8 Ω, 40 Hz to 20 kHz with no more than 0.8% total harmonic distortion.

At Surround operation:
Front channels:		70 W per channel, min. RMS, driven into 8 Ω at 1 kHz with no
		more than 0.8% total harmonic distortion.
Center channel:		70 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than
		0.8% total harmonic distortion.
Rear channels:		70 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
		more than 0.8% total harmonic distortion.
CD, TV, VCR, DVD:		200 mV/47 k Ω
Coaxial:	DIGITAL 1 (DVD):		0.5 V p-p/75 Ω
Optical:	DIGITAL 2 (TV):		–21 dBm to –15 dBm (660 nm ±30 nm)

*Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).

VCR:	200 mV
CD, TV, VCR, DVD: 85 dB/75 dB
CD, TV, VCR, DVD:	20 Hz to 20 kHz (±1 dB)
Bass (100 Hz):	±10 dB
Treble (10 kHz):	±10 dB
+6 dB ± 1 dB at 70 Hz
87.5 MHz to 108.0 MHz
Monaural:	12.8 dBf (1.2 µV/75	Ω)
Monaural:	21.3 dBf (3.2 µV/75	Ω)
Stereo:	41.3 dBf (31.5 µV/75	Ω)
Monaural:	78 dB at 85 dBf
Stereo:	73 dB at 85 dBf
Monaural:	0.4% at 1 kHz
Stereo:	0.6% at 1 kHz
35 dB at 1 kHz
45 dB: (±400 kHz)

30 Hz to 15 kHz: (+0.5 dB, –3 dB)

530 kHz to 1 710 kHz

Loop antenna	400 µV/m
	50 dB (100 mV/m)

AC 120V , 60 Hz

150 W/190 VA (at operation)

2 W (in standby mode)

17 3/16 in. x 3 15/16 in. x 15 11/16 in. (435 mm x 100 mm x 398 mm)

16.4 lbs (7.4 kg)

36

Image 38

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Checking the Supplied Accessories Before InstallationPutting Batteries in the Remote Control Getting StartedStarted Connecting the FM and AM AntennasGetting AM antenna connectionConnecting the front, center, and rear speakers Connecting the SpeakersSpeaker Layout Diagram Connecting the subwooferLeft front speaker Connecting cords are not supplied with this unit. Use Connecting Audio/Video ComponentsConnecting the Power Cord Digital connectionsDVD To increase the volume, press and hold Turn On the PowerTo turn off the power into standby To decrease the volume, press and holdBasic Operations Turning Off the PowerWith the Timer Press Setting Basic SettingsSetting the Digital Input TerminalsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Basic SettingsSelecting the Analog or Digital Input Mode DSP Modes Setting the Subwoofer InformationSetting the Speakers for Press Control 3or 2 to select YESPress Control 3 or 2 to select the appropriate speaker size Delay Time CTR DL, Rear DLEx. When registering the rear speaker size DisplayEx. When adjusting the center delay Press Control 3or 2 to select the delay timeRepeat steps 2 and 3 to adjust the other delay time Crossover Frequency CrossLow Frequency Effect Attenuator LFE Press Control 3or 2 to select the LFE attenuator levelDynamic Range Compression D.R.C To activate Auto Surround, follow the procedure below Setting Auto SurroundTo cancel Auto Surround Each time you press the button, Auto Surround turns on orAttenuating the Input Signal Sound AdjustmentsBasic Settings/Sound Adjustments Adjusting the Front SpeakerPress Control 3 or 2 to turn on or OFF Bass Boost When using the remote controlReinforcing the Bass Adjusting the Subwoofer Output Level Sound AdjustmentsAdjusting the Tone Tuner Operations Tuning in Stations ManuallyUsing Preset Tuning Press FM or AM to select the bandTo restore the stereo effect Selecting the FM Reception ModeTo tune in a preset station Tuner OperationsCreating Realistic Sound Fields DAP Digital Acoustic Processor Modes Available DSP modes according to the input signal formatCreating Realistic Sound Fields Creating sound fieldWhen Auto SR Auto Surround is turned on Surround modeDSP mode About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Press Test to check the speaker output balance Adjust the following speaker output levels from -10 to +10Using Theater Surround Remote Control Press Test again to stop the test toneTo cancel Theater Surround Press Effect to select the DSP effect level 1 to You wantTo cancel DAP Mode Using DAP Modes Remote ControlAdjust the rear speaker output levels from -10 to +10 Digital, or DTS Digital Surround Using Surround Modes Front PanelPress Surround ON/OFF to activate an SeeEx. When adjusting the center speaker output level Using Theater Surround Front PanelPress Control 3or 2 to adjust the speaker output level Using DAP Modes Front Panel Press Control 3or 2 to make an adjustmentRepeat steps 4 and 5 to make other adjustments Ex. When adjusting the left rear speaker output levelMastering Remote Operations Mastering Remote Operations Operating other JVC products Audio/video operation buttonsFront Panel Remote ControlParts Identification Troubleshooting Parts Identification/TroubleshootingFM tuner IHF SpecificationsAmplifier AM tunerMemorandum Source Name1099 781 954 650Valley Road Wayne, NJ Limited Warranty AUDIO-2 0301NHMMDWJEIN