JVC RX-E100SL manual Press Effect to select the DSP effect level 1 to You want

Page 29

2Press DSP MODE repeatedly until “THEATER”

appears on the display.

The PRO LOGIC and DSP indicator light up on the display.

DSP MODE

ANALOG L					R PRO LOGIC

SUBWFR DSP

3Press SOUND.

SOUND

The 10 keys now work for sound adjustments.

4Press TEST to check the speaker output balance.

TEST

1	O LOGIC
	P
	TL AUTO

PUT ATT

VOL

“TEST L” starts flashing on the display, and a test tone comes out of the speakers in the following order:

(Left front speaker)

(Center speaker)

(Right front speaker)

(Left rear speaker)

(Right rear speaker)

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CTR SP” is set to “NO.”

5Adjust the following speaker output levels (from –10 to +10).

•Make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers.

To adjust the center speaker level, press CENTER +/–.

– CENTER +

ANALOG	L	6	C	R	PRO LOGIC
5		6
LPCM	SUBWFR5LFE				DSP
DOLBY D	LS		S	RS	DGTL AUTO	VOL
DTS	LS		S	RS	INPUT ATT	VOL

To adjust the left rear speaker level, press REAR•L +/–.

– REAR•L +

8 ANALOG	L9	C	R	PRO LOGIC
LPCM	SUBWFRMENU		LFE	DSP
5	SUBWFRMENU		LFE	DGTL AUTO
DOLBY D	LS	S	RS	DGTL AUTO
DTS	LS	S	RS	INPUT ATT	VOL

To adjust the right rear speaker level, press REAR•R +/–.

– REAR•R +

ANALOG0	L +10C	R	PRO LOGIC
LPCM	SUBWFRENTERLFE DSP
DOLBY D	LS S	RS	DGTL AUTO	VOL
DTS	LS S	RS	INPUT ATT	VOL

6Press TEST again to stop the test tone.

TEST

1GIC

UTO

TT

VOL

7Press EFFECT to select the DSP effect level (1 to

5) you want.

•As the number increases, the DSP effect becomes stronger (normally set it to “EFFECT 3”).

EFFECT

ANALOG		4L	5	R	PRO LOGIC
			5		DSP
		SUBWFR			DSP
		SUBWFR
		LS S		RS			VOL

To cancel Theater Surround

Press DSP MODE repeatedly until “STEREO” appears on the display. The PRO LOGIC and DSP indicators go off.

Creating Realistic Sound Fields

27

Image 29

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Putting Batteries in the Remote Control Before InstallationChecking the Supplied Accessories Getting StartedGetting Connecting the FM and AM AntennasStarted AM antenna connectionSpeaker Layout Diagram Connecting the SpeakersConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting the Power Cord Connecting Audio/Video ComponentsConnecting cords are not supplied with this unit. Use Digital connectionsDVD To turn off the power into standby Turn On the PowerTo increase the volume, press and hold To decrease the volume, press and holdBasic Operations Turning Off the PowerWith the Timer Setting the Digital Input Basic SettingsPress Setting TerminalsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Basic SettingsSelecting the Analog or Digital Input Mode Setting the Speakers for Setting the Subwoofer InformationDSP Modes Press Control 3or 2 to select YESEx. When registering the rear speaker size Delay Time CTR DL, Rear DLPress Control 3 or 2 to select the appropriate speaker size DisplayRepeat steps 2 and 3 to adjust the other delay time Press Control 3or 2 to select the delay timeEx. When adjusting the center delay Crossover Frequency CrossLow Frequency Effect Attenuator LFE Press Control 3or 2 to select the LFE attenuator levelDynamic Range Compression D.R.C To cancel Auto Surround Setting Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orBasic Settings/Sound Adjustments Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerPress Control 3 or 2 to turn on or OFF Bass Boost When using the remote controlReinforcing the Bass Adjusting the Subwoofer Output Level Sound AdjustmentsAdjusting the Tone Using Preset Tuning Tuning in Stations ManuallyTuner Operations Press FM or AM to select the bandTo tune in a preset station Selecting the FM Reception ModeTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Creating Realistic Sound Fields Available DSP modes according to the input signal formatDAP Digital Acoustic Processor Modes Creating sound fieldDSP mode Surround modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Using Theater Surround Remote Control Adjust the following speaker output levels from -10 to +10Press Test to check the speaker output balance Press Test again to stop the test tonePress Effect to select the DSP effect level 1 to You want To cancel Theater SurroundTo cancel DAP Mode Using DAP Modes Remote ControlAdjust the rear speaker output levels from -10 to +10 Press Surround ON/OFF to activate an Using Surround Modes Front PanelDigital, or DTS Digital Surround SeeEx. When adjusting the center speaker output level Using Theater Surround Front PanelPress Control 3or 2 to adjust the speaker output level Repeat steps 4 and 5 to make other adjustments Press Control 3or 2 to make an adjustmentUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Operating other JVC products Audio/video operation buttons Mastering Remote OperationsFront Panel Remote ControlParts Identification Parts Identification/Troubleshooting TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerSource Name Memorandum1099 781 954 650Valley Road Wayne, NJ Limited Warranty AUDIO-2 0301NHMMDWJEIN