JVC RX-E100SL manual Press Control 3or 2 to make an adjustment, Using DAP Modes Front Panel

Page 33

CENTER : To adjust the center speaker output level (from –10 to +10).

REAR L : To adjust the left rear speaker output level (from –10 to +10).

REAR R : To adjust the right rear speaker output level (from –10 to +10).

EFFECT : To adjust the DSP effect level. As the number increases, the effect becomes stronger (normally set it to “EFFECT 3”).

*“0” is the initial setting for the speaker output levels, and “EFFECT 3” is for the DSP effect level.

If you have already changed the setting, another setting will be shown.

5Press CONTROL 3(or 2) to make an adjustment.

•When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the

same level as that of the front speakers.

CONTROL

ANALOG

L

C

R

PRO LOGIC

 

LPCM

SUBWFR LFE DSP

 

DOLBY D

LS

S

RS

DGTL AUTO

VOL

DTS

INPUT ATT

Ex.: When adjusting the center speaker output level

6Repeat steps 4 and 5 to make other adjustments.

To cancel Theater Surround

Press DSP MODE repeatedly until “STEREO” appears on the display. The PRO LOGIC and DSP indicators go off.

Using DAP Modes (Front Panel)

A DAP mode cannot be used with another DSP mode. Once one of the DAP modes is activated, the other DSP mode in use will be canceled.

•You have to make this adjustment for each source.

•You cannot use any DAP mode if no rear speakers are connected.

1Select and play stereo analog software or Linear PCM digital software.

2Press DSP MODE repeatedly until one of the

DAP modes appears on the display.

The DSP indicator lights up on the display.

DSP

MODE

ANALOG L

R

SUBWFR

 

DSP

LS

S

RS

VOL

3Press ADJUST.

ADJUST

The CONTROL buttons now work for sound

 

adjustments.

4Press CONTROL ° (or 5) repeatedly until one of the following indications (with the current setting)* appears.

CONTROL

 

ANALOG

L

C

R

PRO LOGIC

 

 

 

 

 

 

 

LPCM

SUBWFR LFE DSP

 

 

 

 

 

 

 

DOLBY D

LS

S

RS

DGTL AUTO

 

 

 

VOL

 

 

DTS

INPUT ATT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REAR L : To adjust the left rear speaker output level (from –10 to +10).

REAR R : To adjust the right rear speaker output level (from –10 to +10).

EFFECT : To adjust the DSP effect level. As the number increases, the effect becomes stronger (normally set it to “EFFECT 3”).

*“0” is the initial setting for the speaker output levels, and “EFFECT 3” is for the DSP effect level.

If you have already changed the setting, another setting will be shown.

5Press CONTROL 3(or 2) to make an adjustment.

•When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the

same level as that of the front speakers.

CONTROL

ANALOG

L

C

R

PRO LOGIC

 

LPCM

SUBWFR LFE DSP

 

DOLBY D

LS

S

RS

DGTL AUTO

 

DTS

INPUT ATT

VOL

Ex.: When adjusting the left rear speaker output level

6Repeat steps 4 and 5 to make other adjustments.

To cancel DAP Mode

Press DSP MODE repeatedly so that “STEREO” appears on the display. The DSP indicator goes off.

Creating Realistic Sound Fields

(back to the begining)

31

Page 32 Page 34
Image 33
Page 32 Page 34
Contents RX-E100SL For Canada/pour Le Canada Table of Contents Putting Batteries in the Remote Control Before InstallationChecking the Supplied Accessories Getting StartedGetting Connecting the FM and AM AntennasStarted AM antenna connectionSpeaker Layout Diagram Connecting the SpeakersConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting the Power Cord Connecting Audio/Video ComponentsConnecting cords are not supplied with this unit. Use Digital connectionsDVD To turn off the power into standby Turn On the PowerTo increase the volume, press and hold To decrease the volume, press and holdTurning Off the Power With the TimerBasic Operations Setting the Digital Input Basic SettingsPress Setting TerminalsBasic Settings Selecting the Analog or Digital Input ModeWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Setting the Speakers for Setting the Subwoofer InformationDSP Modes Press Control 3or 2 to select YESEx. When registering the rear speaker size Delay Time CTR DL, Rear DLPress Control 3 or 2 to select the appropriate speaker size DisplayRepeat steps 2 and 3 to adjust the other delay time Press Control 3or 2 to select the delay timeEx. When adjusting the center delay Crossover Frequency CrossPress Control 3or 2 to select the LFE attenuator level Dynamic Range Compression D.R.CLow Frequency Effect Attenuator LFE To cancel Auto Surround Setting Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orBasic Settings/Sound Adjustments Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerWhen using the remote control Reinforcing the BassPress Control 3 or 2 to turn on or OFF Bass Boost Sound Adjustments Adjusting the ToneAdjusting the Subwoofer Output Level Using Preset Tuning Tuning in Stations ManuallyTuner Operations Press FM or AM to select the bandTo tune in a preset station Selecting the FM Reception ModeTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Creating Realistic Sound Fields Available DSP modes according to the input signal formatDAP Digital Acoustic Processor Modes Creating sound fieldDSP mode Surround modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Using Theater Surround Remote Control Adjust the following speaker output levels from -10 to +10Press Test to check the speaker output balance Press Test again to stop the test tonePress Effect to select the DSP effect level 1 to You want To cancel Theater SurroundUsing DAP Modes Remote Control Adjust the rear speaker output levels from -10 to +10To cancel DAP Mode Press Surround ON/OFF to activate an Using Surround Modes Front PanelDigital, or DTS Digital Surround SeeUsing Theater Surround Front Panel Press Control 3or 2 to adjust the speaker output levelEx. When adjusting the center speaker output level Repeat steps 4 and 5 to make other adjustments Press Control 3or 2 to make an adjustmentUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Operating other JVC products Audio/video operation buttons Mastering Remote OperationsRemote Control Parts IdentificationFront Panel Parts Identification/Troubleshooting TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerSource Name Memorandum781 954 650 Valley Road Wayne, NJ1099 Limited Warranty AUDIO-2 0301NHMMDWJEIN
Top Page Image Contents