JVC RX-E100SL Tuner Operations, Tuning in Stations Manually, Press FM or AM to select the band

Page 22

Tuner Operations

You can also use the remote control for some tuner operations.

• When using the remote control, see also “Mastering Remote Operations” on page 32.

CONTROL

5/°/3/2 Display

STANDBY
POWER	RX-E100	HOME THEATER RECEIVER

CONTROL

ANALOG

L

C

R

PRO LOGIC

SLEEP

TUNED

ST

AUTO

MUTING

LPCM

SUBWFR LFE DSP

MH

DOLBY D

LS

S

RS

DGTL AUTO

KH

INPUT

SURROUND

DSP

SETTING

ADJUST

MEMORY

DTS

INPUT ATT

VOL

ANALOG/DIGITAL

ON/OFF

MODE

MASTER VOLUME

INPUT ATT

D I G I T A L

DVD

TV

VCR

CD

FM

AM

S U R R O U N D

D I G I T A L

MEMORY	Source selecting buttons
	(FM, AM)

Tuning in Stations Manually	Remote
	NOT

1Press FM or AM to select the band.

The last received station of the selected band is tuned in, and the CONTROL buttons now work for tuner operations.

FM	TUNED	ST	AUTO	MUTING
FM	AM			MHZ

VOL

Ex.: When selecting the FM band

Using Preset Tuning

Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 30 FM and 15 AM stations.

To store the preset stations	Remote
Before you start, remember...	NOT
Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

2Press CONTROL ° (or 5) repeatedly until “< TUNING >” appears on the display.

CONTROL

TUNED ST AUTO MUTING

VOL

Then

TUNED	ST	AUTO	MUTING
			MHZ

VOL

1Tune in the station you want to preset (see “Tuning in Stations Manually”).

•If you want to store the FM reception mode for this station, select the FM reception mode you want. See “Selecting the FM Reception Mode” on page 21.

ANALOG L			R	TUNED ST AUTO MUTING

MHZ

VOL

2Press MEMORY.

3Press repeatedly or hold CONTROL 3or 2 until you find the frequency you want.

The channel number position starts flashing on the display for about 10 seconds.

MEMORY

CONTROL

TUNED ST AUTO MUTING

MHZ

VOL

TUNED ST AUTO MUTING

MHZ

VOL

•Pressing (or holding) CONTROL 3increases the frequencies.

•Pressing (or holding) CONTROL 2decreases the frequencies.

3Press CONTROL 3 (or 2) to select a channel number while the channel number position is flashing.

Notes:

•When you hold and release CONTROL 3 or CONTROL 2, the frequency keeps changing until a station is tuned in.

•When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display.

•When an FM stereo program is received, the ST (Stereo) indicator also lights up.

CONTROL

TUNED ST AUTO MUTING

MHZ

VOL

20

Image 22

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Checking the Supplied Accessories Before InstallationPutting Batteries in the Remote Control Getting StartedStarted Connecting the FM and AM AntennasGetting AM antenna connectionConnecting the front, center, and rear speakers Connecting the SpeakersSpeaker Layout Diagram Connecting the subwooferLeft front speaker Connecting cords are not supplied with this unit. Use Connecting Audio/Video ComponentsConnecting the Power Cord Digital connectionsDVD To increase the volume, press and hold Turn On the PowerTo turn off the power into standby To decrease the volume, press and holdWith the Timer Turning Off the PowerBasic Operations Press Setting Basic SettingsSetting the Digital Input TerminalsSelecting the Analog or Digital Input Mode Basic SettingsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off DSP Modes Setting the Subwoofer InformationSetting the Speakers for Press Control 3or 2 to select YESPress Control 3 or 2 to select the appropriate speaker size Delay Time CTR DL, Rear DLEx. When registering the rear speaker size DisplayEx. When adjusting the center delay Press Control 3or 2 to select the delay timeRepeat steps 2 and 3 to adjust the other delay time Crossover Frequency CrossDynamic Range Compression D.R.C Press Control 3or 2 to select the LFE attenuator levelLow Frequency Effect Attenuator LFE To activate Auto Surround, follow the procedure below Setting Auto SurroundTo cancel Auto Surround Each time you press the button, Auto Surround turns on orAttenuating the Input Signal Sound AdjustmentsBasic Settings/Sound Adjustments Adjusting the Front SpeakerReinforcing the Bass When using the remote controlPress Control 3 or 2 to turn on or OFF Bass Boost Adjusting the Tone Sound AdjustmentsAdjusting the Subwoofer Output Level Tuner Operations Tuning in Stations ManuallyUsing Preset Tuning Press FM or AM to select the bandTo restore the stereo effect Selecting the FM Reception ModeTo tune in a preset station Tuner OperationsCreating Realistic Sound Fields DAP Digital Acoustic Processor Modes Available DSP modes according to the input signal formatCreating Realistic Sound Fields Creating sound fieldWhen Auto SR Auto Surround is turned on Surround modeDSP mode About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Press Test to check the speaker output balance Adjust the following speaker output levels from -10 to +10Using Theater Surround Remote Control Press Test again to stop the test toneTo cancel Theater Surround Press Effect to select the DSP effect level 1 to You wantAdjust the rear speaker output levels from -10 to +10 Using DAP Modes Remote ControlTo cancel DAP Mode Digital, or DTS Digital Surround Using Surround Modes Front PanelPress Surround ON/OFF to activate an SeePress Control 3or 2 to adjust the speaker output level Using Theater Surround Front PanelEx. When adjusting the center speaker output level Using DAP Modes Front Panel Press Control 3or 2 to make an adjustmentRepeat steps 4 and 5 to make other adjustments Ex. When adjusting the left rear speaker output levelMastering Remote Operations Mastering Remote Operations Operating other JVC products Audio/video operation buttonsParts Identification Remote ControlFront Panel Troubleshooting Parts Identification/TroubleshootingFM tuner IHF SpecificationsAmplifier AM tunerMemorandum Source NameValley Road Wayne, NJ 781 954 6501099 Limited Warranty AUDIO-2 0301NHMMDWJEIN