FR SP (Front Speaker) | : To register the front speaker size. |
CTR SP (Center Speaker) : To register the center speaker size.
REAR SP (Rear Speaker) : To register the rear speaker size.
*“LRG (large)” is the initial setting for the front speakers, and “SML (small)” is for the center and rear speakers.
If you have already changed the setting, another size will be shown.
3Press CONTROL 3 (or 2) to select the appropriate speaker size.
•Each time you press the button, the speaker size changes as follows:
CONTROL |
|
|
| ||
ANALOG | L | C | R | PRO LOGIC |
|
LPCM | SUBWFR LFE | DSP |
| ||
DOLBY D | LS | S | RS | DGTL AUTO | VOL |
DTS | INPUT ATT | ||||
Ex.: When registering the rear speaker size
LRG (Large) : Select this when the speaker size is relatively large. (See “Notes” below.)
SML (Small) : Select this when the speaker size is relatively small. (See “Notes” below.)
NO | : Select this when you have not connected a |
| speaker. (Not selectable for the front speakers) |
|
|
4Repeat steps 2 and 3 to select the appropriate size for the other speakers.
Notes:
•Use the following criteria as reference when adjusting:
–If the size of the cone speaker unit built in your speaker is greater than 4 3/4 inches (12 cm ), select “LRG (large),” and if it is smaller than 4 3/4 inches (12 cm ), select “SML (small).”
•If you have selected “NO” for the subwoofer, you can only select “LRG (large)” for the front speaker size.
•If you have selected “SML (small)” for the front speaker size, you cannot select “LRG (large)” for the center and rear speaker sizes.
Delay Time — CTR DL, REAR DL
Adjust the delay time of the sounds from the center speaker and from the rear speakers, comparing to that of the sounds from the front speakers. If the distance to the center speaker and/or the rear speakers from your listening point is almost the same as that to the front speakers, select 0 msec.
•1 msec increase (or decrease) in delay time corresponds to 1 foot (30 cm) increase (or decrease) in distance.
Left front |
|
|
| Right front |
speaker |
| Center speaker |
| speaker |
|
|
|
|
|
10 feet
(3.0 m)
9 feet
(2.7 m)
8 feet
(2.4 m)
7 feet
(2.1 m)
Left rear | Right rear |
speaker | speaker |
Ex.: In this case, set the center delay to “1 mS” and the rear delay to “2 mS.”
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
1Press SETTING.
SETTING | The CONTROL buttons now work for basic |
| |
| settings. |
2Press CONTROL ° (or 5) repeatedly until “CTR DL (Center Delay)” or “REAR DL (Rear Delay” (with the current setting) * appears on the
display.
CONTROL |
|
|
|
| |
ANALOG | L | C | R | PRO LOGIC |
|
LPCM | SUBWFR LFE | DSP |
| ||
DOLBY D | LS | S | RS | DGTL AUTO | VOL |
DTS | INPUT ATT | ||||
Basic Settings
CTR DL (Center Delay) : To adjust the center delay time (from 0 msec to 5 msec).
REAR DL (Rear Delay) : To adjust the rear delay time (from 0 msec to 15 msec).
*“0 mS (msec)” is the initial setting for the center delay time and
“5 mS (msec)” for the rear delay time. If you have already changed the setting, another setting will be shown.
TO BE CONTINUED TO THE NEXT PAGE
13