JVC RX-E100SL manual Creating Realistic Sound Fields, DAP Digital Acoustic Processor Modes

Page 25

DAP (Digital Acoustic Processor) Modes

DAP modes have been designed to create important acoustic surround elements.

The sound heard in a hall, live club, dance club or pavilion consists of direct sound and indirect sound — early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are delayed by the distances of the ceiling and walls (see the diagram to the right).

These indirect sounds are important elements of the acoustic surround effects.

The following DAP modes are provided with this receiver.

LIVE CLUB : Gives the feeling of a live music club with a low ceiling.

DANCE CLUB : Gives a throbbing bass beat.

HALL

: Gives clear vocal and the feeling of a concert

 

hall.

 

 

PAVILION

: Gives the spacious feeling of a pavilion with a

 

high ceiling.

 

 

These DAP modes can be used to add the acoustic surround effects while reproducing stereo analog software or Linear PCM digital software, and can give you a real “being there” feeling.

DAP modes can be used when the front and rear speakers are connected to this receiver (without respect to the center speaker connection: no sound comes out of the center speaker if it is connected).

When one of the DAP modes is selected, the DSP indicator lights up on the display.

Creating sound field

Reflections from behind

Early reflections

Direct sounds

Creating Realistic Sound Fields

Available DSP modes according to the input signal format

: Possible : Impossible

DSP Modes

format

Analog

Linear PCM

Signal

Dolby Digital

Input

DTS

 

 

 

SURROUND

THEATER

LIVE CLUB DANCE CLUB

HALL

PAVILION

STEREO

(Dolby Pro Logic)

(Dolby Pro Logic)

*1

(Dolby Digital)

*2

(DTS Digital Surround)

*1 Dolby Digital is activated except when 2 channel signals come in (in this case, Dolby Pro Logic is activated).

*2 DTS Digital Surround is activated except when 2 channel signals come in (in this case, Dolby Pro Logic is activated).

23

Image 25
Contents RX-E100SL For Canada/pour Le Canada Table of Contents Putting Batteries in the Remote Control Before InstallationChecking the Supplied Accessories Getting StartedGetting Connecting the FM and AM AntennasStarted AM antenna connectionSpeaker Layout Diagram Connecting the SpeakersConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting the Power Cord Connecting Audio/Video ComponentsConnecting cords are not supplied with this unit. Use Digital connectionsDVD To turn off the power into standby Turn On the PowerTo increase the volume, press and hold To decrease the volume, press and holdWith the Timer Turning Off the PowerBasic Operations Setting the Digital Input Basic SettingsPress Setting TerminalsSelecting the Analog or Digital Input Mode Basic SettingsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Setting the Speakers for Setting the Subwoofer InformationDSP Modes Press Control 3or 2 to select YESEx. When registering the rear speaker size Delay Time CTR DL, Rear DLPress Control 3 or 2 to select the appropriate speaker size DisplayRepeat steps 2 and 3 to adjust the other delay time Press Control 3or 2 to select the delay timeEx. When adjusting the center delay Crossover Frequency CrossDynamic Range Compression D.R.C Press Control 3or 2 to select the LFE attenuator levelLow Frequency Effect Attenuator LFE To cancel Auto Surround Setting Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orBasic Settings/Sound Adjustments Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerReinforcing the Bass When using the remote controlPress Control 3 or 2 to turn on or OFF Bass Boost Adjusting the Tone Sound AdjustmentsAdjusting the Subwoofer Output Level Using Preset Tuning Tuning in Stations ManuallyTuner Operations Press FM or AM to select the bandTo tune in a preset station Selecting the FM Reception ModeTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Creating Realistic Sound Fields Available DSP modes according to the input signal formatDAP Digital Acoustic Processor Modes Creating sound fieldDSP mode Surround modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Using Theater Surround Remote Control Adjust the following speaker output levels from -10 to +10Press Test to check the speaker output balance Press Test again to stop the test tonePress Effect to select the DSP effect level 1 to You want To cancel Theater SurroundAdjust the rear speaker output levels from -10 to +10 Using DAP Modes Remote ControlTo cancel DAP Mode Press Surround ON/OFF to activate an Using Surround Modes Front PanelDigital, or DTS Digital Surround SeePress Control 3or 2 to adjust the speaker output level Using Theater Surround Front PanelEx. When adjusting the center speaker output level Repeat steps 4 and 5 to make other adjustments Press Control 3or 2 to make an adjustmentUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Operating other JVC products Audio/video operation buttons Mastering Remote OperationsParts Identification Remote ControlFront Panel Parts Identification/Troubleshooting TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerSource Name MemorandumValley Road Wayne, NJ 781 954 6501099 Limited Warranty AUDIO-2 0301NHMMDWJEIN