JVC RX-E100SL manual Getting Started, Before Installation, Putting Batteries in the Remote Control

Page 4

Getting Started

Before Installation

General Precautions

•DO NOT insert any metal object into the receiver.

•DO NOT disassemble the receiver or remove screws, covers, or cabinet.

•DO NOT expose the receiver to rain or moisture.

Locations

•Install the receiver in a location that is level and protected from moisture.

•The temperature around the receiver must be between 23˚F and 95˚F (–5˚C and 35˚C).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Putting Batteries in the Remote Control

Before using the remote control, put two supplied batteries first.

•When using the remote control, aim the remote control directly at the remote sensor on the receiver.

1.On the back of the remote control, remove the battery cover.

2

1

Handling the receiver

•DO NOT touch the power cord with wet hands.

•DO NOT pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

•Keep the power cord away from the connecting cords and the antenna. The power cord may cause noise or screen interference. It is recommended to use a coaxial cable for antenna connection, since it is well-shielded against interference.

•When a power failure occurs, or when you unplug the power cord, the preset settings such as preset FM/AM channels and sound adjustments may be erased in a few days.

2.Insert batteries. Make sure to match the polarity:

(+) to (+) and (–) to (–).

Checking the Supplied Accessories

Check to be sure you have all of the following supplied accessories. The number in the parentheses indicates the quantity of the pieces supplied.

•Remote Control (1)

•Batteries (2)

•AM Loop Antenna (1)

•FM Antenna (1)

If anything is missing, contact your dealer immediately.

3. Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity: (+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

2

Image 4

Contents RX-E100SL For Canada/pour Le Canada Table of Contents Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Getting StartedConnecting the FM and AM Antennas GettingStarted AM antenna connectionConnecting the Speakers Speaker Layout DiagramConnecting the front, center, and rear speakers Connecting the subwooferLeft front speaker Connecting Audio/Video Components Connecting the Power CordConnecting cords are not supplied with this unit. Use Digital connectionsDVD Turn On the Power To turn off the power into standbyTo increase the volume, press and hold To decrease the volume, press and holdWith the Timer Turning Off the PowerBasic Operations Basic Settings Setting the Digital InputPress Setting TerminalsSelecting the Analog or Digital Input Mode Basic SettingsWhen Dgtl D.D. or Dgtl DTS is selected, Auto goes off Setting the Subwoofer Information Setting the Speakers forDSP Modes Press Control 3or 2 to select YESDelay Time CTR DL, Rear DL Ex. When registering the rear speaker sizePress Control 3 or 2 to select the appropriate speaker size DisplayPress Control 3or 2 to select the delay time Repeat steps 2 and 3 to adjust the other delay timeEx. When adjusting the center delay Crossover Frequency CrossDynamic Range Compression D.R.C Press Control 3or 2 to select the LFE attenuator levelLow Frequency Effect Attenuator LFE Setting Auto Surround To cancel Auto SurroundTo activate Auto Surround, follow the procedure below Each time you press the button, Auto Surround turns on orSound Adjustments Basic Settings/Sound AdjustmentsAttenuating the Input Signal Adjusting the Front SpeakerReinforcing the Bass When using the remote controlPress Control 3 or 2 to turn on or OFF Bass Boost Adjusting the Tone Sound AdjustmentsAdjusting the Subwoofer Output Level Tuning in Stations Manually Using Preset TuningTuner Operations Press FM or AM to select the bandSelecting the FM Reception Mode To tune in a preset stationTo restore the stereo effect Tuner OperationsCreating Realistic Sound Fields Available DSP modes according to the input signal format Creating Realistic Sound FieldsDAP Digital Acoustic Processor Modes Creating sound fieldSurround mode DSP modeWhen Auto SR Auto Surround is turned on About Relations between Speaker Layout and DSP ModesUsing Surround Modes Remote Control Adjust the following speaker output levels from -10 to +10 Using Theater Surround Remote ControlPress Test to check the speaker output balance Press Test again to stop the test toneTo cancel Theater Surround Press Effect to select the DSP effect level 1 to You wantAdjust the rear speaker output levels from -10 to +10 Using DAP Modes Remote ControlTo cancel DAP Mode Using Surround Modes Front Panel Press Surround ON/OFF to activate anDigital, or DTS Digital Surround SeePress Control 3or 2 to adjust the speaker output level Using Theater Surround Front PanelEx. When adjusting the center speaker output level Press Control 3or 2 to make an adjustment Repeat steps 4 and 5 to make other adjustmentsUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Mastering Remote Operations Operating other JVC products Audio/video operation buttonsParts Identification Remote ControlFront Panel Troubleshooting Parts Identification/TroubleshootingSpecifications AmplifierFM tuner IHF AM tunerMemorandum Source NameValley Road Wayne, NJ 781 954 6501099 Limited Warranty AUDIO-2 0301NHMMDWJEIN