Basic Settings
CONTROL | Display |
5/°/3/2 | |
STANDBY |
|
POWER |
|
|
| CONTROL |
| ANALOG | L | C | R | PRO LOGIC | SLEEP | TUNED | ST | AUTO | MUTING |
|
|
|
|
|
|
| LPCM | SUBWFR LFE DSP |
|
|
|
| MH |
|
|
| |||
|
|
|
| DOLBY D | LS | S | RS | DGTL AUTO |
|
|
|
| KH | INPUT | SURROUND | DSP |
SETTING | ADJUST |
| MEMORY | DTS | INPUT ATT |
|
|
|
| VOL | ||||||
|
|
|
|
|
|
|
|
|
|
| ANALOG/DIGITAL | ON/OFF | MODE | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MASTER VOLUME |
|
|
|
|
|
|
|
|
|
|
|
|
|
| INPUT ATT |
|
|
D I G I T A L |
|
|
| DVD |
|
| TV | VCR | CD | FM |
|
| AM |
|
| |
|
|
|
|
|
|
|
|
|
| |||||||
S U R R O U N D D I G I T A L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SETTING |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Setting the Subwoofer Information | Remote |
NOT |
When you have connected a subwoofer, follow the procedure below. If you do not use a subwoofer, you can skip this setting.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
1Press SETTING.
SETTING | The CONTROL buttons now work for basic |
| |
| settings. |
2Press CONTROL ° (or 5) repeatedly until “SUBWFR (Subwoofer)” (with the current
setting)* appears on the display.
CONTROL
Setting the Speakers for | Remote |
DSP Modes | NOT |
To obtain the best possible surround effect from the DSP (Digital Signal Processor) modes (see page 22), register the following information after all connections are completed.
•Speaker Size — FR SP, CTR SP, REAR SP
•Delay Time — CTR DL, REAR DL
•Crossover Frequency — CROSS
•Dynamic Range Compression — D.R.C.
•Low Frequency Effect Attenuator — LFE
Speaker Size — FR SP, CTR SP, REAR SP
Register the sizes of all the connected speakers.
•When you change your speakers, register the information about the speakers again.
GIC
UTO
TT | VOL |
*“NO” is the initial setting. If you have already changed the setting, “YES” will be shown.
3Press CONTROL 3(or 2) to select “YES.”
• Each time you press the button, the subwoofer setting
alternates between “YES” and “NO.”
CONTROL
ANALOG | L | C | R | PRO LOGIC |
|
LPCM | SUBWFR LFE DSP |
| |||
DOLBY D | LS | S | RS | DGTL AUTO | VOL |
DTS | INPUT ATT | ||||
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
1Press SETTING.
SETTING | The CONTROL buttons now work for basic |
| settings. |
2Press CONTROL ° (or 5) repeatedly until one of the following speakers (with the current setting)* appears.
CONTROL
ANALOG | L | C | R PRO LOGIC | ||
LPCM | SUBWFR LFE DSP | ||||
DOLBY D | LS | S | RS | DGTL AUTO | |
DTS | INPUT ATT | ||||
|
|
| |||
|
|
|
|
| |
VOL |
YES : Select this when a subwoofer is used.
The subwoofer speaker indicator (SUBWFR) lights up on the display (see page 9). You can adjust the subwoofer output level (see page 19).
NO : Select this when you have not connected or have disconnected a subwoofer.
12