JVC RX-9010VBK manual Adjusting the Main Room Volume, Activating the Main Room Front Speakers

MASTER VOLUME

From the remote control:

DVD	DVDMULTI	PHONO	CD
VCR 1	VCR 2	TAPE/MD	CDR
TV/DBS	VIDEO	FM/AM	USB AUDIO

Note:

Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source.

Speaker and signal indicators on the display

By checking the following indicators, you can easily confirm which speakers you are activating and which signals are coming into this receiver from the source.

Speaker indicators (white) Signal indicators (red)

L C	R	L	C	R
SUBWFR				LFE
LS	RS	LS	S	RS

The speaker indicators

The indicators correspond to the speakers as follows:

Frame	Speaker
L	Left front	It always lights while the main
		room is activated.
R	Right front
C	Center	It lights when you set the
		corresponding speaker correctly.
LS	Left rear
		(For details, see page 29.)
RS	Right rear
		It always lights when
SUBWFR	Subwoofer	“SUBWOOFER” is set to “YES.”*
		(For details, see page 28.)

The signal indicators

The signal indicators light in the following cases:

•When the DIGITAL input mode (see page 31) is selected, only the indicators for the incoming signals light.

•When the ANALOG input mode (see page 31) is selected, the indicators light as follows:

-When selecting “DVD MULTI” (see pages 9 and 49), all the signal indicators except “S” always light on the display.

-When selecting the sources other than “DVD MULTI,” only “L” and “R” always light on the display.

To bring out the best performance of this receiver, check the speaker and signal indicators on the display carefully and set the speakers correctly.

L	C R
	LFE Ex.The center signals are coming
LS	RS	from the source, but the center
		speaker is not prepared.

Notes:

•“S” is the monaural rear signal. It is automatically mixed down to “LS” and “RS.”

•“LFE” signals are automatically mixed down to the other signals when you select the digital input mode. However, when you select “DVD MULTI,” this receiver reproduces the LFE signals only

through subwoofer channel.

*When you do not press SUBWOOFER OUT ON/OFF to deactivate the subwoofer.

Adjusting the Main Room Volume

On the front panel:

To increase the volume, turn MASTER VOLUME clockwise. To decrease the volume, turn it

counterclockwise.

•When you turn MASTER VOLUME rapidly, the volume level also changes rapidly.

•When you turn MASTER VOLUME slowly, the volume level also changes slowly.

From the remote control:

To increase the volume, press VOLUME +.

To decrease the volume, press VOLUME –. VOLUME

CAUTIONS:

•Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

•Be careful not to turn up the volume so high when controlling the receiver without listening to the playback sound. For example, when adjusting the volume level in the sub-room from the main room.

Notes:

•The volume level can be adjusted within the range of “0” (minimum) to “90” (maximum).

•If you set One Touch Operation to “ON” (see page 34), you do not have to adjust the volume level each time you change the source. It is automatically set to the stored level for the previous setting.

Activating the Main Room Front Speakers

When shipped from the factory, both pairs of the front speakers have been set to be used in the main room.

•To use the front speakers connected to the FRONT 2/SUB ROOM SPEAKERS terminals for the sub-room, see “Setting the Front Speakers Either for the Main Room or Sub-room” on page 27, and “Activating the Sub-room Front Speakers” on page 26.

IMPORTANT:

You can activate two pairs of the front speakers at the same time only when the SPEAKER LOAD SELECTOR switch on the rear panel is set to the “HIGH” position and when no signals are sent to the center and rear speakers. Otherwise, activating one pair of the speakers deactivates the other.

19