JVC RX-9010VBK manual Adjust the liveness, Press DSP Mode repeatedly until

8.Adjust the liveness.

1)Press EFFECT repeatedly until “LIVENESS” appears on the display. The display changes to show the current setting.

2)Press CONTROL UP 5/DOWN °to select the liveness level you want.

•Each time you press the button, the display changes to show the following:

EFFECT

CONTROL

DOWN UP

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 29).

•This function does not work when you activate the sub-room.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

•You cannot adjust the center speaker output level and select the center tone level for 4 CH Stereo mode.

•To adjust the front speaker output balance and subwoofer output level, see pages 27 and 28.

LIVENESS 1 LIVENESS 2 LIVENESS 3

LIVENESS 5 LIVENESS 4

As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.” (Normally set it to “LIVENESS 3.”)

On the front panel:

1. Press DSP MODE repeatedly until	DSP MODE
“5CH STEREO*” appears on the
display.

The DSP MODE lamp on the front panel button lights up, and the DSP indicator also lights up on the display.

*“4CH STEREO” appears on the display when you have set “CTR SPK” to “NONE.” (See page 29.)

Adjusting the 5 CH/4 CH Stereo Mode

IMPORTANT:

Check to see if the proper indicator(s) and information appear on the display on the front panel before/while using the buttons and controls.

For the main room operations:

•The MAIN ROOM indicator is lit.

•The source name for the sub-room is not lit on the display.

•When using the remote control:

–Set MAIN ROOM/SUB ROOM selector to

“MAIN ROOM.”

– Check to see if the following information
	MAIN ROOM SUB ROOM
appear on the display window on the remote
control.

2.Adjust the speaker output levels.

1)Press LEVEL ADJUST repeatedly until one of the following indications appears on the display.

“CENTER”: (for 5CH STEREO only) To adjust the center speaker level.

“REAR L”:

To adjust the left rear speaker level. “REAR R”:

To adjust the right rear speaker level.

2)Press CONTROL UP 5/DOWN ° to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

LEVEL

ADJUST

CONTROL

DOWN UP

3. Adjust the center tone (for 5CH STEREO only.)

	Buttons	Indications
	SOUND	SOUND
After pressing SOUND, the following function are
assigned to the specific number buttons:
	Buttons	Indications
	CENTER TONE	SOUND
	CENTER	CTR
	REAR•L	REARL
	REAR•R	REARR

1)Press EFFECT repeatedly until “CTR TONE” appears on the display.

The display changes to show the current setting.

2)Press CONTROL UP 5/DOWN ° to select the center tone level you want.

•The center tone adjustment affects the mid-frequency range, which the human voice is mostly made up of.

•Each time you press the button, the display changes to show the following:

EFFECT

CONTROL

DOWN UP

Ex. “SOUND” appears on the display		STANDBY	ON
	MAIN ROOM SUB ROOM
	MAIN ROOM	SUB ROOM TV/CATV/DBS	VCR1
window.	ON/OFF	ON/OFF POWER	POWER

MAIN ROOM SUB ROOM

When you press the buttons listed above, the indication appears for 5 – 10 seconds for your confirmation.

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

CTR TONE 5	CTR TONE 4
(Sharper)	(Sharp)

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or

“CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

Continued to the next page.

46