JVC RX-9010VBK manual Adjusting the Surround Modes with DAP Modes

From the remote control:

1. Press DSP MODE repeatedly until the DSP

DAP mode you want to adjust — MODE

THEATER 1, THEATER 2, HALL 1, HALL 2, LIVE CLUB, DANCE

CLUB, or PAVILION — appears on the display.

The DSP MODE lamp on the front panel button lights up, and the DSP indicator also lights up on the display.

•When you have set “REAR SPK” to “NONE,” the 3D- PHONIC indicator also lights up.

2. Press SOUND. SOUND

The 10 keys are activated for sound adjustments.

3.Select the speaker you want to adjust.

•To select the center speaker level, press CENTER.

•To select the left rear speaker level, press REAR•L.

•To select the right rear speaker level, press REAR•R.

CENTER REAR·L REAR·R

47/P8

4. Press LEVEL + or LEVEL – to

LEVEL+

adjust the speaker output levels (–

10 dB toLEVEL–

+10 dB).

• Each time you press the button, the

indication corresponding to the button selected in step 3 appears on the display window on the remote control.

5.Repeat steps 3 and 4 to adjust the other speaker output levels.

6. Press CENTER TONE to select									CENTER TONE
the center tone level you want.									+10
• Each time you press the button, the display									100+
	changes to show the following:
		CTR TONE 1		CTR TONE 2				CTR TONE 3
		(Softer)			(Soft)				(Flat)
			CTR TONE 5			CTR TONE 4
			(Sharper)				(Sharp)

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

8. Press ROOM SIZE to adjust the	ROOM SIZE
room size (sense of spaciousness).	6

•Each time you press the button, the display changes to show the following:

ROOMSIZE 1 ROOMSIZE 2 ROOMSIZE 3

ROOMSIZE 5 ROOMSIZE 4

As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. (Normally set it to “ROOMSIZE 3.”)

9. Press LIVENESS to adjust the	LIVENESS
	9
liveness.

•Each time you press the button, the display changes to show the following:

LIVENESS 1 LIVENESS 2 LIVENESS 3

LIVENESS 5 LIVENESS 4

As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.” (Normally set it to “LIVENESS 3.”)

Adjusting the Surround Modes with the

DAP Modes

IMPORTANT:

Check to see if the proper indicator(s) and information appear on the display on the front panel before/while using the buttons and controls.

For the main room operations:

•The MAIN ROOM indicator is lit.

•The source name for the sub-room is not lit on the display.

•When using the remote control:

– Set MAIN ROOM/SUB ROOM selector to

“MAIN ROOM.”

– Check to see if the following information

appear on the display window on the remote			MAIN ROOM SUB ROOM
control.
	Buttons	Indications
	SOUND	SOUND
	After pressing SOUND, the following function are
	assigned to the specific number buttons:
	Buttons	Indications
	EFFECT
	ROOM SIZE	SOUND
	LIVENESS

7. Press EFFECT to adjust the

EFFECT

CENTER TONE

overall level of the effect.

3

CENTER	CTR
REAR•L	REARL

•Each time you press the button, the effect level changes as follows:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5 EFFECT 4

As the number increases, the selected DAP effect becomes stronger. (Normally set it to “EFFECT 3.”)

REAR•R REARR

MAIN ROOM	SUB ROOM	STANDBY	ON
MAIN ROOM	SUB ROOM	TV/CATV/DBS	VCR1
ON/OFF	ON/OFF	POWER	POWER

Ex. “SOUND” appears on the display

window. MAIN ROOM SUB ROOM

When you press the buttons listed above, the indication appears

for 5 – 10 seconds for your confirmation.

43