JVC RX-9010VBK manual Cross Over appears on Display, Press Control UP 5/ Down Control

Center speaker

Front speaker Front speaker

3.0 m

2.7 m

2.4 m

2.1 m

Low Frequency Effect Attenuator Setting

If the bass sound is distorted while playing back a source using Dolby Digital or DTS Digital Surround, follow the procedure below.

On the front panel ONLY:

1. Press SETTING repeatedly until	SETTING
“LFE ATT” (Low Frequency Effect
Attenuator) appears on the display.

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN ° CONTROL

to select the low frequency effect attenuator level.

DOWN UP

Rear speakers

EX. In this case, set the center delay time to “1 ms” and the rear delay time to “2 ms.”

Crossover Frequency Setting

Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocate the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker).

To use this function properly, you need to set the crossover frequency level according to the size of the small speaker connected.

•If you have selected “LARGE” for all speakers (see page 29), this function cannot be adjusted.

On the front panel ONLY:

1. Press SETTING repeatedly until	SETTING
“CROSS OVER” appears on the
display.
The display changes to show the current setting.

2. Press CONTROL UP 5/ DOWN ° CONTROL

• Each time you press the button, the display changes to show the following:

0dB 10dB

0dB: Normally select this.

10dB: Select this when the bass sound is distorted.

Notes:

•Low frequency effect attenuator is not valid for the DVD MULTI playback mode.

•This function takes effect only when the Dolby Digital or DTS Digital Surround sounds with LFE signals comes in and “SUBWOOFER” is set to “YES.”

Digital Input (DIGITAL IN) Terminal

Setting

When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL 1/2/3/4).

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

to select the crossover frequency level according to the size of the small speaker connected.

DOWN UP

To set the DIGITAL 1 terminal:

1. Press SETTING repeatedly until	SETTING
“DGTL COAX” (Digital Coaxial)

•Each time you press the button, the display changes to show the following:

80Hz100Hz120Hz

• Use the following comments as reference when adjusting:

80Hz:	Select this when the cone speaker unit built in the
	speaker is about 4 3/4 inches (12 cm).
100Hz:	Select this when the cone speaker unit built in the
	speaker is about 3 15/16 inches (10 cm).
120Hz:	Select this when the cone speaker unit built in the
	speaker is about 3 3/16 inches (8 cm).

Note:

Crossover frequency is not valid for the DVD MULTI playback mode,

5 CH/4 CH Stereo mode, 3D-PHONIC mode, and HEADPHONE DSP mode.

appears on the display.

The display changes to show the current setting for DIGITAL 1 terminal.

2. Press CONTROL UP 5/DOWN °	CONTROL
	DOWN UP
to select the appropriate digital
terminal setting.

•Each time you press the button, the display changes to show the following:

1:DVD Ò1: MD** Ò1: CDR Ò 1: TV (or DBS* ) Ò1: CD Ò(back to the beginning)

*If you have changed the source name from “TV” to “DBS,” “DBS” appears (see page 33).

**Change the source name to “MD” for TAPE/MD terminals when you use an MD recorder (see page 33).

Continued to the next page.

30