JVC RX-9010VBK manual Operating JVC’s Audio/Video Components, Operating Audio Components, Tuner

Page 68

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC audio components through the COMPU LINK-4 (SYNCHRO) jacks (see page 55) in addition to the connections using cables with RCA pin plugs (see pages 7 and 8).

•Aim the remote control directly at the remote sensor on the receiver.

•If you use the buttons on the front panel or the menu function to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selecting buttons on the remote control.

•To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 33.)

•Refer also to the manuals supplied with your components.

Tuner

You can always perform the following operations:

FM/AM:Alternates between FM and AM.

After pressing FM/AM, you can perform the following operations:

1 – 10, +10:Selects a preset channel number directly. For channel number 5, press 5.

For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.

TUNING UP/DOWN: Tunes into stations.

FM MODE:Changes the FM reception mode.

Sound control section (Amplifier)

When using the remote control supplied with this receiver:

•For the main room operations

–Set MAIN ROOM/SUB ROOM selector to “MAIN ROOM.”

•For the sub-room operations

–Set MAIN ROOM/SUB ROOM selector to

“SUB ROOM.”

–Check to see if the following information appear on the display window on the remote

control:

MAIN ROOM SUB ROOM

 

 

 

 

 

 

 

MAIN ROOM/

Indications

 

 

SUB ROOM selector

 

 

 

 

 

 

 

MAIN ROOM

MAIN ROOM *

 

SUB ROOM

SUB ROOM *

 

 

 

 

 

*MAIN ROOM or SUB ROOM indicator does not appear when no indicators appear on the display window.

 

Buttons

Indications

 

FM/AM

TUNER

 

CD

CD

 

CDR

CDR

 

PHONO

PHONO

 

TAPE/MD

TAPE

CONTROL (repeatedly)

VCR1 =TAPE =CDR =

CDDSC =(back to the beginning)

 

 

 

 

 

SOUND

SOUND

 

 

 

 

 

After selecting a source:

 

 

 

 

 

 

 

 

 

Buttons

Indications

 

 

 

 

 

 

 

 

PLAY

 

 

 

 

4/REW

 

 

one of the selected

 

 

FF/¢

 

 

source names listed

 

 

STOP

 

 

above

 

 

PAUSE

 

 

 

 

 

1 – 10, +10, 0

 

 

 

 

 

 

 

 

After pressing SOUND, the following function are assigned to the specific number buttons:

You can always perform the following operations:

SURROUND ON/OFF:

Turns on or off the Surround modes

 

— Dolby Pro Logic, Dolby Digital,

 

and DTS Digital Surround.

DSP MODE:

Selects the DSP modes.

TEST:

Turns on or off the test tone output.

After pressing SOUND, you can perform the following operations:

SUBWFR then LEVEL +/–:

Adjusts the subwoofer output level.

CENTER then LEVEL +/–:

Adjusts the center speaker output

 

level.

REAR•L then LEVEL +/–:

Adjusts the left rear speaker output

 

level.

REAR•R then LEVEL +/–:

Adjusts the right rear speaker output

 

level.

DIGITAL EQ then LEVEL +/–: Selects the audio band and adjusts its frequency level.

BALANCE L/BALANCE R: Adjusts the output balance of the

 

front speakers.

EFFECT:

Selects the effect level.

CENTER TONE:

Selects the center tone.

ROOM SIZE:

Selects the room size.

LIVENESS:

Selects the liveness.

Notes:

•After adjusting sounds, press the corresponding source selecting button to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.

•Each time you press LEVEL + or LEVEL –, the indication corresponding to the function you have selected appears on the display window on the remote control.

CD player

Buttons

Indications

 

 

BALANCE L

 

BALANCE R

 

EFFECT

SOUND

ROOM SIZE

 

LIVENESS

 

CENTER TONE

 

SUBWFR

S WFR

CENTER

CTR

REAR•L

REARL

REAR•R

REARR

DIGITAL EQ

EQ

 

 

When you press the buttons listed above, the indication appears for 5 – 10 seconds for your confirmation.

After pressing CD, you can perform the following operations on the CD player:

PLAY:

Starts playing.

4:

Returns to the beginning of the current (or

¢:

previous) track.

Skips to the beginning of the next track.

STOP:

Stops playing.

PAUSE:

Pauses playing. To release it, press PLAY.

1 – 10, +10:

Selects a track number directly.

 

For track number 5, press 5.

 

For track number 15, press +10, then 5.

 

For track number 20, press +10, then 10.

 

For track number 30, press +10, +10, then 10.

65

Page 67 Page 69
Image 68
Page 67 Page 69
Contents RX-9010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Features Precautions IntroductionParts Identification Front PanelDVD MULTI, DVD, VCR 1, VCR 2, Video AUDIO, FM/AMRemote Control TV/CATV/DBS POWER, VCR 1 Power 67Before Installation Checking the Supplied AccessoriesConnecting the FM and AM Antennas Getting StartedConnecting the Speakers Basic connecting procedureConnecting the front speakers AM Antenna ConnectionsConnecting Audio/Video Components Connecting the rear and center speakersConnecting the subwoofer speaker Analog ConnectionsCD recorder Cassette deck or MD recorderVCRs SOUND/DBS, do not connect the TV’s video Output to these video input jacksTo audio OutputDigital output terminal Digital ConnectionsDigital input terminals Change the PC audio setting USB ConnectionLamp on the USB Audio button lights up USB cableRotate the fixing nut to attach the RF rod antenna firmly Find the place where you attach the IR signal transmitterInsert the RF rod antenna to the RF Remote Antenna terminal Connecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Replace the coverMulti-room Operations Required Speaker Connections for the Sub-roomMerits DemeritsBasic Operating Procedure for Main Room Press PowerPress Audio Power on Select and play a sourceStandby lamp on the front panel Basic Operating Procedure for Sub-RoomSet Main ROOM/SUB Room selector to SUB Room For the main room operations Turning the Power On and Off StandbyMain Room Basic Operations Canceling the Main Room Operations Selecting the Main Room Source to PlaySelecting different sources for picture and sound To stop the main room operations and sounds from the mainAdjusting the Main Room Volume Speaker and signal indicators on the displaySpeaker indicators Signal indicatorsAdjusting the Equalization Patterns Listening at Night Midnight Mode Reinforcing the Bass Attenuating the Input SignalActivating the Subwoofer Sound Muting the Main Room SoundRecording a Source Selecting the Line Direct Function Using the Sleep TimerChanging the Display Brightness Sub-Room Operations Press SUB Room ON/OFF. SUB Room on /OFFPress SUB Room CONTROL. SUB Room Control For the sub-room operationsCanceling the Sub-room Operations To turn off the power into standby mode, pressAudio Power Standby SUB Room ON/OFFAdjusting the Sub-room Volume To increase the volume, turn MasterTo decrease the volume, turn it counterclockwise To increase the volume, press Volume +Activating the Sub-room Front Speakers Muting the Sub-room SoundThrough the front speaker in the sub Room Operating the Playback Source for Sub-roomBasic Settings Setting the Front Speakers Either for Main Room or Sub-roomAdjusting the Front Speaker Output Balance To adjust the balanceAdjusting the Subwoofer Output Level Setting the Subwoofer InformationSetting the Speakers for a Surround Field Digital Input Digital in Terminal Setting To select the appropriate digital Terminal settingCross Over appears on Display Press Control UP 5/ Down ControlTerminal settings Selecting the Analog or Digital Input ModeWhich you want to change the input mode To set the Digital 2/3/4 terminalsTo select the appropriate video Input terminal Selecting the Video Input TerminalVideo DVD or Video DBS Appears on the display Changing the Source Name Showing the Text Information on DisplayBasic Setting and Adjustment Auto Memory To store the volume levelTo recall the volume level To cancel the One Touch OperationReceiving Radio Broadcasts Using Preset TuningTuning in Stations Manually Selecting the FM Reception Mode DSP modes Creating a Surround Field in the Main RoomSurround modes DVD Multi Playback Mode Headphone DSP modeReproducing the Sound Field 3D-PHONIC modesAvailable DSP Modes According to the Speaker Arrangement Available DSP modesTheater \ Theater Live Club \ Dance Club \ PavilionAdjusting the Surround Modes Adjust the center tone Adjusting the DAP ModesPress Center Tone to select the center tone level you want CTR Tone 1 CTR Tone 2 CTR ToneDance CLUB, or Pavilion appears on the display Adjust the overall levels of the effect. EffectAdjust the room size sense of spaciousness Adjusting the Surround Modes with DAP Modes Adjust the speaker output levels 10 dB to +10 dB Press DSP Mode repeatedly until DAP mode you want to adjustPress Effect to adjust the overall Press Surround ON/OFF to Activate an appropriate SurroundActivate an appropriate Surround Adjust the liveness Press DSP Mode repeatedly untilAdjusting the 5 CH/4 CH Stereo Mode Adjust the center tone for 5CH Stereo onlyAdjusting the 3D-PHONIC Modes Center tone level you want for 5CH +10Stereo only Center CTR Rearl Rearr3D Action or 3D Digital Press Center to select the center speakerUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModeAdjust the speaker output levels From -10 dB to +10 dB Press DVD Multi so that DVDUsing the On-Screen Menus Press %/ Þto move to the frequency you want to adjust Press %/ Þto move to Sound CONTROL, then press @/ #Press @/ # WantPress %/ Þto move to Mode you want toSelect DVD Multi as the playing source To Line Direct Press @/ #to turnLine direct function On or OFFPress %/ Þto move to SETTING, then press @/ # Storing the Preset Stations Also seeSetting the Basic Setting Items Press %/ Þto move to Tuner CONTROL, then press @/ #Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverRX-9010VBK TurntableSynchronized Recording Same timePress the play 3 button on the CD player Text Compu Link Remote Control System CD player MD recorderDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerPress Text Display while CD or MD is selected as the source Disc Information screenShowing the Disc Information on the TV Screen To exit from the Disc information screenPress Text Display while CD is selected as the source Press %/ Þto move to SEARCH, then pressPress %/ Þto move to Performer Then press SET Press SET againPress %/ Þto move to SEARCH, then press SET Press %/ Þto move To GENRE, then Press SETPress %/ Þto move To Title INPUT, then press SET Entering the Disc InformationPress %/ Þto move to the genre you want, then press SET Press Text Display while MD is selected as the sourcePress %/ Þto move to Title Input Then press SET For the MD recorderAV Compu Link Remote Control System Connections 1 IR Signal Transmitter ConnectionIR signal transmitter Connections 2 AV Comp Link ConnectionTo the TVs’ Video Input 1 terminal using S-video cables Connections 3 Video Cable ConnectionCase One-Touch Video PlayOne-Touch DVD Play Automatic Power On/Off StandbyAutomatic Power On Operating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD player-changer CD recorderTurntable Cassette deckOperating Video Components TV/CATV/DBS selectorMain ROOM/SUB Room selector VCR VCR connected to the VCR 1 jacksEnter manufacturer’s code using buttons 1-9, Release TV/CATV/DBS PowerOperating Other Manufacturers’ Equipment Try to operate your TV by pressingRelease VCR 1 Power Try to operate your VCR by pressing VCR 1 PowerVCR 1 Power If there are more than one code listed for your brandRelease Audio Power on If there are more than one code listed for your brand of CDManufactures codes for TV Manufacturer Codes Manufactures codes for DBS tuner Manufacturer CodesManufactures codes for Catv converter Manufacturer Codes Manufactures codes for VCR Manufacturer CodesManufactures codes for DVD player Manufacturer Codes Manufactures codes for CD player Manufacturer CodesTroubleshooting Problem Possible Cause SolutionCATV/DBS Specifications AmplifierFM tuner IHF AM tunerQualityservice Factory Service Center Locations781 954 650 Valley Road Wayne, NJLimited Warranty AUDIO-2 0201NHMMDWJEIN
Top Page Image Contents