JVC RX-9010VBK manual Receiving Radio Broadcasts, Using Preset Tuning, Tuning in Stations Manually

Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.

•You can use “On-screen Menu” for most of the main room operations. For details, see page 50.

Indicates the functions YOU CAN ALSO USE when the receiver is ready for the sub-room operations.

IMPORTANT:

Check to see if the proper indicator(s) and information(s) appear on the display on the front panel before/while using the buttons and controls.

2. Press TUNING UP

or TUNING DOWN	/REW	PLAY	FF/
	DOWN	TUNING	UP
until you find the
frequency you want.

•Pressing TUNING UP increases the frequency.

•Pressing TUNING DOWN decreases the frequency.

When using the buttons and controls on the front panel:

•For the main room operations

–The MAIN ROOM indicator is lit.

–The source name for the sub-room is not lit on the display.

•For the sub-room operations

–The SUB ROOM indicator is lit.

–The source name for the sub-room is lit on the display.

When using the remote control:

•For the main room operations

– Set MAIN ROOM/SUB ROOM selector to

“MAIN ROOM.”

• For the sub-room operations

MAIN ROOM SUB ROOM

–Set MAIN ROOM/SUB ROOM selector to

“SUB ROOM.”

Notes:

•When a station of sufficient signal strength is tuned in, the TUNED indicator lights on the display.

•When an FM stereo program is received, the STEREO indicator also lights up.

•When you hold the button (and release it) in step 2, the frequency keeps changing until a station is tuned in.

•You can only select the same station of the same band (FM or AM) both for the main room and sub-room operations. If you change the station for the sub-room, it also changes for the main room (and vice versa). This also means that if you change the station for the sub-room while recording a broadcasting program in the main room, recording in the main room will be interrupted.

Using Preset Tuning

Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 30 FM and 15 AM stations.

Tuning in Stations Manually

On the front panel:

1. Press FM/AM to select the band (FM or AM).

FM/AM

To store the preset stations

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

The last received station of the selected band is tuned in.

•Each time you press the button, the band alternates between FM and AM.

For the main room

			AUTO MUTING	TUNED STEREO
ANALOG	L	R
					MAIN ROOM
	SPEAKERS				VOLUME
	1

For the sub-room

AUTO MUTING	TUNED STEREO
SPEAKERS		SUB ROOM
SUB ROOM		VOLUME

On the front panel ONLY:

1.Tune in the station you want to preset (see “Tuning in Stations Manually” to the left).

•If you want to store the FM reception mode for this station, select the FM reception mode you want. See “Selecting the FM Reception Mode” on page 36.

			AUTO MUTING	TUNED STEREO
ANALOG	L	R
					MAIN ROOM
	SPEAKERS				VOLUME
	1

2. Press MEMORY. MEMORY

2. Press FM/AM TUNING 5/° until you find the frequency you want.

FM/AM TUNING

ANALOG	L	R	AUTO MUTING	TUNED STEREO
				MAIN ROOM
	SPEAKERS			VOLUME
	1

•Pressing FM/AM TUNING 5increases the frequency.

•Pressing FM/AM TUNING °decreases the frequency.

The channel number position starts flashing on the display for about 10 seconds.

From the remote control:

1. Press FM/AM to select the band (FM FM/AM or AM).

The last received station of the selected band is tuned in.

•Each time you press the button, the band alternates between FM and AM.

3. Press FM/AM PRESET 5/° to select a channel number while the channel number position is flashing.

FM/AM PRESET

35