JVC RX-9010VBK manual Specifications, Amplifier, FM tuner IHF, AM tuner, General

Page 77

Specifications

Designs & specifications are subject to change without notice.

Amplifier

Output Power

At Stereo operation:

Front channels: 120 W per channel, min. RMS, driven into 8 Ω, 20 Hz to 20 kHz with no more than 0.02% total harmonic distortion.

120 W per channel, min. RMS, driven into 4 Ω, 20 Hz to 20 kHz with no more than 0.08% total harmonic distortion.

At Surround operation:

Front channels: 100 W per channel, min. RMS, driven into 8 Ω at 1 kHz with no more than 0.8% total harmonic distortion.

Center channel: 100 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than 0.8% total harmonic distortion.

Rear channels: 100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no more than 0.8% total harmonic distortion.

Audio

Audio Input Sensitivity/Impedance (1 kHz): PHONO (MM): 2.5 mV/47 kΩ

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD: 200 mV/47 kΩ

Audio Input (DIGITAL IN)* :

Coaxial: DIGITAL 1 (DVD): 0.5 V(p-p)/75 Ω

Optical: DIGITAL 2 (CD), DIGITAL 3 (TV), DIGITAL 4 (CDR): –21 dBm to –15 dBm (660 nm ±30 nm)

*Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency

—32 kHz, 44.1 kHz, 48 kHz).

USB:Revision 1.0, Full-speed (with sampling frequency

— 32 kHz, 44.1 kHz, 48 kHz)

Audio Output Level:

SUB ROOM PRE OUT: 200 mV

Recording Output Level: TAPE/MD, VCR 1, VCR 2, CDR: 200 mV

Digital output: Optical:

DIGITAL OUTPUT

Signal wave length:

660 nm

Output level:

–21 dBm to –15 dBm

Signal-to-Noise Ratio (’66 IHF/’78 IHF):

PHONO: 70 dB/78 dB (at REC OUT)

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD:

92 dB/80 dB (Line Direct On)

Frequency Response (8 Ω): PHONO: 20 Hz to 20 kHz (±1 dB)

VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD,

DVD CENTER, DVD REAR, DVD FRONT

 

: 20 Hz to 20 kHz (±1 dB, –3 dB)

USB

: 20 Hz to 20 kHz (±1 dB, –3 dB)

RIAA Phono Equalization: ±1.0 dB (20 Hz to 20 kHz)

Bass boost (Volume control at –30 dB): +6 ±1.0 dB at 100 Hz

Video

Video Input Sensitivity/Impedance:

Composite video: DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS: 1 V(p-p)/75 Ω

S-video: DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS: (Y: luminance): 1 V(p-p)/75Ω

(C: chrominance, burst): 0.286 V(p-p)/75 Ω

Component: DVD, DBS

(Y: luminance): 1 V(p-p)/75 Ω

(PB, PR): ±0.7 V/75 Ω

Video Output Level:

Composite video: VCR 1, VCR 2, MONITOR OUT: 1 V(p-p)/75 Ω

S-video: VCR 1, VCR 2, MONITOR OUT:

(Y: luminance): 1 V(p-p)/75 Ω

(C: chrominance, burst): 0.286 V(p-p)/75 Ω

Component: MONITOR OUT

(Y: luminance): 1 V(p-p)/75 Ω

(PB, PR): ±0.7 V/75 Ω

Synchronization: Negative

Signal-to-Noise Ratio: 45 dB

On-Screen Color System: NTSC

FM tuner (IHF)

Tuning Range: 87.5 MHz to 108.0 MHz

Usable Sensitivity: Monaural:12.8 dBf (1.2 µV/75 Ω)

50 dB Quieting Sensitivity:

 

 

Monaural:

21.3 dBf (3.2 µV/75

Ω)

Stereo:

41.3 dBf (31.5 µV/75

Ω)

Signal-to-Noise Ratio (IHF-A weighted):

 

Monaural:

78 dB at 85 dBf

 

Stereo:

73 dB at 85 dBf

 

Total Harmonic Distortion:

 

 

Monaural:

0.4% at 1 kHz

 

Stereo:

0.6% at 1 kHz

 

Stereo Separation at REC OUT: 35 dB at 1 kHz

Alternate Channel Selectivity: 45 dB: (±400 kHz)

Frequency Response: 30 Hz to 15 kHz: (+0.5 dB, –3 dB)

AM tuner

Tuning Range: 530 kHz to 1 710 kHz

Usable Sensitivity: Loop antenna: 400 µV/m

Signal-to-Noise Ratio: 50 dB (100 mV/m)

General

Power Requirements: AC 120V , 60 Hz

Power Consumption: 320 W/440 VA (at operation) 2 watts (in standby mode)

Dimensions (W x H x D): 435 mm x 156.5 mm x 425.1 mm (17 3/16 in. x 6 3/16 in. x 16 3/4 in.)

Mass:

11.6 kg (25.6 lbs)

74

Page 76 Page 78
Image 77
Page 76 Page 78
Contents RX-9010VBK Mises en garde, précautions et indications diverses For Canada/pour Le Canada Table of Contents Introduction Features PrecautionsFront Panel Parts IdentificationDVD MULTI, DVD, VCR 1, VCR 2, Video AUDIO, FM/AMTV/CATV/DBS POWER, VCR 1 Power 67 Remote ControlChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers AM Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker Analog ConnectionsCD recorder Cassette deck or MD recorderVCRs Output to these video input jacks SOUND/DBS, do not connect the TV’s videoTo audio OutputDigital output terminal Digital ConnectionsDigital input terminals USB Connection Change the PC audio settingLamp on the USB Audio button lights up USB cableRotate the fixing nut to attach the RF rod antenna firmly Find the place where you attach the IR signal transmitterInsert the RF rod antenna to the RF Remote Antenna terminal Putting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Replace the coverRequired Speaker Connections for the Sub-room Multi-room OperationsMerits DemeritsPress Power Basic Operating Procedure for Main RoomPress Audio Power on Select and play a sourceStandby lamp on the front panel Basic Operating Procedure for Sub-RoomSet Main ROOM/SUB Room selector to SUB Room For the main room operations Turning the Power On and Off StandbyMain Room Basic Operations Selecting the Main Room Source to Play Canceling the Main Room OperationsSelecting different sources for picture and sound To stop the main room operations and sounds from the mainSpeaker and signal indicators on the display Adjusting the Main Room VolumeSpeaker indicators Signal indicatorsAdjusting the Equalization Patterns Attenuating the Input Signal Listening at Night Midnight Mode Reinforcing the BassActivating the Subwoofer Sound Muting the Main Room SoundRecording a Source Selecting the Line Direct Function Using the Sleep TimerChanging the Display Brightness Press SUB Room ON/OFF. SUB Room on /OFF Sub-Room OperationsPress SUB Room CONTROL. SUB Room Control For the sub-room operationsTo turn off the power into standby mode, press Canceling the Sub-room OperationsAudio Power Standby SUB Room ON/OFFTo increase the volume, turn Master Adjusting the Sub-room VolumeTo decrease the volume, turn it counterclockwise To increase the volume, press Volume +Muting the Sub-room Sound Activating the Sub-room Front SpeakersThrough the front speaker in the sub Room Operating the Playback Source for Sub-roomSetting the Front Speakers Either for Main Room or Sub-room Basic SettingsAdjusting the Front Speaker Output Balance To adjust the balanceSetting the Subwoofer Information Adjusting the Subwoofer Output LevelSetting the Speakers for a Surround Field To select the appropriate digital Terminal setting Digital Input Digital in Terminal SettingCross Over appears on Display Press Control UP 5/ Down ControlSelecting the Analog or Digital Input Mode Terminal settingsWhich you want to change the input mode To set the Digital 2/3/4 terminalsTo select the appropriate video Input terminal Selecting the Video Input TerminalVideo DVD or Video DBS Appears on the display Showing the Text Information on Display Changing the Source NameTo store the volume level Basic Setting and Adjustment Auto MemoryTo recall the volume level To cancel the One Touch OperationReceiving Radio Broadcasts Using Preset TuningTuning in Stations Manually Selecting the FM Reception Mode DSP modes Creating a Surround Field in the Main RoomSurround modes Headphone DSP mode DVD Multi Playback ModeReproducing the Sound Field 3D-PHONIC modesAvailable DSP modes Available DSP Modes According to the Speaker ArrangementTheater \ Theater Live Club \ Dance Club \ PavilionAdjusting the Surround Modes Adjusting the DAP Modes Adjust the center tonePress Center Tone to select the center tone level you want CTR Tone 1 CTR Tone 2 CTR ToneDance CLUB, or Pavilion appears on the display Adjust the overall levels of the effect. EffectAdjust the room size sense of spaciousness Adjusting the Surround Modes with DAP Modes Press DSP Mode repeatedly until DAP mode you want to adjust Adjust the speaker output levels 10 dB to +10 dBPress Effect to adjust the overall Press Surround ON/OFF to Activate an appropriate SurroundActivate an appropriate Surround Press DSP Mode repeatedly until Adjust the livenessAdjusting the 5 CH/4 CH Stereo Mode Adjust the center tone for 5CH Stereo onlyCenter tone level you want for 5CH +10 Adjusting the 3D-PHONIC ModesStereo only Center CTR Rearl RearrPress Center to select the center speaker 3D Action or 3D DigitalActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModeAdjust the speaker output levels From -10 dB to +10 dB Press DVD Multi so that DVDUsing the On-Screen Menus Press %/ Þto move to Sound CONTROL, then press @/ # Press %/ Þto move to the frequency you want to adjustPress @/ # WantPress %/ Þto move to Mode you want toSelect DVD Multi as the playing source Press @/ #to turn To Line DirectLine direct function On or OFFStoring the Preset Stations Also see Press %/ Þto move to SETTING, then press @/ #Setting the Basic Setting Items Press %/ Þto move to Tuner CONTROL, then press @/ #Remote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemRX-9010VBK TurntableSynchronized Recording Same timePress the play 3 button on the CD player CD player MD recorder Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerDisc Information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen To exit from the Disc information screenPress %/ Þto move to SEARCH, then press Press Text Display while CD is selected as the sourcePress %/ Þto move to Performer Then press SET Press SET againPress %/ Þto move To GENRE, then Press SET Press %/ Þto move to SEARCH, then press SETPress %/ Þto move To Title INPUT, then press SET Entering the Disc InformationPress Text Display while MD is selected as the source Press %/ Þto move to the genre you want, then press SETPress %/ Þto move to Title Input Then press SET For the MD recorderConnections 1 IR Signal Transmitter Connection AV Compu Link Remote Control SystemIR signal transmitter Connections 2 AV Comp Link ConnectionConnections 3 Video Cable Connection To the TVs’ Video Input 1 terminal using S-video cablesCase One-Touch Video PlayOne-Touch DVD Play Automatic Power On/Off StandbyAutomatic Power On Operating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section AmplifierCD recorder CD player-changerTurntable Cassette deckTV/CATV/DBS selector Operating Video ComponentsMain ROOM/SUB Room selector VCR VCR connected to the VCR 1 jacksRelease TV/CATV/DBS Power Enter manufacturer’s code using buttons 1-9,Operating Other Manufacturers’ Equipment Try to operate your TV by pressingTry to operate your VCR by pressing VCR 1 Power Release VCR 1 PowerVCR 1 Power If there are more than one code listed for your brandIf there are more than one code listed for your brand of CD Release Audio Power onManufactures codes for TV Manufacturer Codes Manufactures codes for DBS tuner Manufacturer CodesManufactures codes for VCR Manufacturer Codes Manufactures codes for Catv converter Manufacturer CodesManufactures codes for DVD player Manufacturer Codes Manufactures codes for CD player Manufacturer CodesProblem Possible Cause Solution TroubleshootingCATV/DBS Amplifier SpecificationsFM tuner IHF AM tunerFactory Service Center Locations Qualityservice781 954 650 Valley Road Wayne, NJLimited Warranty AUDIO-2 0201NHMMDWJEIN
Top Page Image Contents