JVC RX-9010VBK manual Press %/ Þto move to Sound CONTROL, then press @/ #, Press @/ #, Want, @ / #

Adjusting the Equalization Patterns

(Also see page 20)

1. Press MENU.

The MENU appears on the TV.

•Pressing one of the %/ Þ/ @/ #buttons also displays the MENU.

2.Press %/ Þto move to “SOUND CONTROL,” then press @/ #.

The SOUND CONTROL menu appears.

For Surround modes and Surround mode with DAP

mode:
“TEST TONE”:	Output a test tone.
“L/R BALANCE”:	Adjust the right and left balance
	of the front speakers.

“CENTER LEVEL”: Adjust the center speaker output level. *

“REAR L LEVEL”: Adjust the left rear speaker output level. **

“REAR R LEVEL”: Adjust the right rear speaker output level. **

3.Press %/ Þto move to “DIGITAL EQ,” then

press @/ #.

The DIGITAL EQ menu appears.

4.Press %/ Þto move to the frequency you want to adjust.

5.Press @/ #to adjust the frequency level you

want.

The frequency level changes by 2 dB from –8 dB to +8 dB.

SOUND CONTROL

￿ DIGITAL EQ￿ LEVEL ADJUST￿ EFFECT ADJUST￿

MIDNIGHT MODE: NORMAL￿

INPUT ATT : NORMAL￿

LINE DIRECT: OFF￿

BASS BOOST : OFF￿

SUBWOOFER : ON￿

￿

￿:ENTER

DIGITAL EQ

￿FRONT 63Hz : 0dB￿ FRONT 250Hz : 0dB￿ FRONT 1kHz : 0dB￿ FRONT 4kHz : 0dB￿ FRONT 16kHz : 0dB￿

￿

:OPERATE

“SUBWFR LEVEL”: Adjust the subwoofer output level. ***

For DAP mode:

“L/R BALANCE”: Adjust the right and left balance of the front speakers.

“CENTER LEVEL”: Adjust the center speaker output level. *

“REAR L LEVEL”: Adjust the left rear speaker output level. **

“REAR R LEVEL”: Adjust the right rear speaker output level. **

“SUBWFR LEVEL”: Adjust the subwoofer output level. ***

For 5 CH/4 CH Stereo mode:

“L/R BALANCE”: Adjust the right and left balance of the front speakers.

6.When you finish, press EXIT repeatedly until the menu disappears from the TV.

Adjusting the Surround and DSP Modes

(Also see pages 40 – 48)

You can use a Surround mode with a DAP mode, but not with the 5 CH/4 CH Stereo mode and 3D PHONIC mode.

1. Press MENU.

The MENU appears on the TV.

•Pressing one of the %/ Þ/ @/ #buttons also displays the MENU.

2.Select Surround mode and/or DSP mode you like to adjust (see page 50).

3.Press %/ Þto move to “SOUND CONTROL,” then press @/ #.

The SOUND CONTROL menu appears.

“CENTER LEVEL”: Adjust the center speaker output level. ****

“REAR L LEVEL”: Adjust the left rear speaker output level. **

“REAR R LEVEL”: Adjust the right rear speaker output level. **

“SUBWFR LEVEL”: Adjust the subwoofer output level. ***

For 3D-PHONIC mode:

“L/R BALANCE”: Adjust the right and left balance of the front speakers.

“CENTER LEVEL”: Adjust the center speaker output level. *

“SUBWFR LEVEL”: Adjust the subwoofer output level.***

For SURR. OFF (DSP OFF):

“L/R BALANCE”: Adjust the right and left balance

4.Press %/ Þto move to “LEVEL ADJUST,”

then press @/ #.

The LEVEL ADJUST menu appears.

5.Press %/ Þto move to the item you want to set or adjust, then press

@/ #.

On these adjustment menus, you can do the following:

SOUND CONTROL
DIGITAL EQ￿￿
LEVEL ADJUST		￿
EFFECT ADJUST
MIDNIGHT MODE: NORMAL ￿
INPUT ATT	: NORMAL￿
LINE DIRECT: OFF		￿
BASS BOOST	: OFF￿
SUBWOOFER	: ON ￿
￿

:ENTER

LEVEL ADJUST

￿￿
￿
TEST TONE : OFF￿
L/R BALANCE : CENTER￿
CENTER LEVEL:	0dB￿
REAR L LEVEL:	0dB￿
REAR R LEVEL:	0dB￿
SUBWFR LEVEL:	0dB￿
￿	:OPERATE

￿

of the front speakers.

“SUBWFR LEVEL”: Adjust the subwoofer output level.***

Notes:

*You cannot select “CENTER LEVEL” when “CTR SPK” is set to “NONE” (see page 29).

**You cannot select both “REAR L LEVEL” and “REAR R LEVEL” when “REAR SPK” is set to “NONE” (see page 29).

***You cannot select “SUBWFR LEVEL” when “SUBWFR” is set to “NO” (see page 28).

****You cannot select “CENTER LEVEL” when 4 CH Stereo mode is selected.

6.Press EXIT once.

51