Operating Other Manufacturers’ Equipment

This remote control supplied with the receiver can transmit control signals for other manufacturers’ VCRs, TVs, CATV converters, DBS tuners, DVD players ,and CD players. By changing the transmittable signals from preset ones to the other manufacturers’, you can operate the other manufacturer’s components using this remote control.

When operating the other manufacturers’ components, refer also to the manuals supplied with them. To operate these components with the remote control, first you need to set the manufacturer’s code each for VCR, TV, CATV converter, DBS tuner, and DVD player.

After replacing batteries of the remote control, set the manufactures’ codes again.

IMPORTANT:

•To operate the video component(s) using the RF signals emitted from this remote control, the IR signal transmitter and the RF rod antenna must be connected to this receiver.

–Place the IR signal transmitter so that it is aimed at the remote sensor on the target video component(s).

–The RF signal-reachable distance may differ depending on the operating conditions and circumstances.

–The IR signal transmitter can send signals at a distance of 10 feet (3 m).

When using the remote control:

To change the transmittable signals for operating another manufacturer’s TV

1.Set TV/CATV/DBS selector to “TV.”

2.Press and hold TV/CATV/DBS POWER.

3.Press TV/DBS.

Check to see if TV/CATV/DBS selector are set to the correct position:

TV/CATV/DBS selector:

• For TV operations

Set TV/CATV/DBS selector to “TV.”	TV
• For the CATV converter and DBS tuner
	CATV/
	DBS
operations
Set TV/CATV/DBS selector to “ CATV/DBS.”

•Check to see if the following information appear on the display window on the remote control.

After setting the remote control mode selector to “TV” :

Buttons	Indications

TV/DBS	TV
VCR 1	VCR 1
DVD or DVD MULTI	DVD
CD	CD
DVD MENU	DMENU

After setting the remote control mode selector to “CATV/DBS” :

	Buttons	Indications

	TV/DBS	CATV
	VCR 1	VCR 1
DVD or DVD MULTI		DVD
	CD	CD
	DVD MENU	DMENU
	After selecting a source:

	Buttons	Indications

	PLAY
	4	one of the source
	¢	one of the source
	STOP	names listed above
	PAUSE
	1 – 9, 0, +10, 100+
	CHANNEL +/–	VCR1 or TV
	After pressing DVD MENU:

	Buttons	Indications
	%, Þ, @, #, SET	DMENU

4. Enter manufacturer’s code using buttons 1–9, and 0.

See page 70 to find the code.

5. Release TV/CATV/DBS POWER.

After setting TV/CATV/DBS selector to “TV,” you can perform the following operations on the TV:

TV/CATV/DBS POWER: Turns on and off the TV.

TV VOL +/–:Adjusts the volume.

TV/VIDEO:Sets the input mode (either TV or VIDEO).

After pressing TV/DBS (with the remote control mode selector set to “TV”), you can perform the following operations on a TV:

CHANNEL +/–:	Changes the channels.
1 – 10, 0, 100+ (+10):	Selects the channels.
	The 10 button will function as the
	ENTER button if your TV requires
	pressing ENTER after selecting a
	channel number.

Notes:

•Refer to the manual supplied with your TV.

•You cannot change the channels of some TVs by pressing number buttons. In this case, press CHANNEL +/– for changing the channels.

6.Try to operate your TV by pressing

TV/CATV/DBS POWER.

When your TV turns on or off, you have entered the correct code.

If there are more than one code listed for your brand of TV,

try each one until the correct one is entered.

When you press the buttons listed above, the indication appears for 5 – 10 seconds for your confirmation.

Note:

All the functions may not be assigned to the buttons in some equipment.

Continued to the next page.