JVC RX-9010VBK Press Center Tone to select the center tone level you want, Adjust the center tone

CENTER TONE

+10

100+

9. Press CENTER TONE to select the center tone level you want.

The center tone adjustment affects the mid- frequency range, which the human voice is mostly made up of.

•Each time you press the button, the display changes to show the following:

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

4.Adjust the center tone.

1)Press EFFECT repeatedly until “CTR TONE” appears on the display.

The display changes to show the current setting.

2)Press CONTROL UP 5/DOWN °to select the center tone level you want.

•Each time you press the button, the display changes to show the following:

EFFECT

CONTROL

DOWN UP

CTR TONE 5	CTR TONE 4
(Sharper)	(Sharp)

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with DOLBY SURROUND mark.

• To enjoy Dolby Digital, play back a software encoded with Dolby

Digital and labeled with mark.

D I G I T A L

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND ON/OFF to	SURROUND ON/OFF
activate an appropriate Surround
mode — PRO LOGIC, DOLBY
DIGITAL or DTS SURROUND.

The SURROUND ON/OFF lamp on the front panel button lights up.

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

3. Adjust the speaker output levels.	LEVEL
	ADJUST

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

CTR TONE 5	CTR TONE 4
(Sharper)	(Sharp)

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR

TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

Adjusting the DAP Modes

You can also use a DAP mode with a Surround mode (see page 43).

IMPORTANT:

Check to see if the proper indicator(s) and information appear on the display on the front panel before/while using the buttons and controls.

For the main room operations:

•The MAIN ROOM indicator is lit.

•The source name for the sub-room is not lit on the display.

•When using the remote control:

– Set MAIN ROOM/SUB ROOM selector to

“MAIN ROOM.”
– Check to see if the following information
			MAIN ROOM SUB ROOM
appear on the display window on the remote
control.
	Buttons	Indications
	SOUND	SOUND
	After pressing SOUND, the following function are
	assigned to the specific number buttons:

1)Press LEVEL ADJUST repeatedly until one of the following indications appears on the display.

“CENTER”:

To adjust the center speaker level. “REAR L”:

To adjust the left rear speaker level. “REAR R”:

To adjust the right rear speaker level.

2)Press CONTROL UP 5/DOWN °to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

CONTROL

DOWN UP

Buttons	Indications
EFFECT
ROOM SIZE	SOUND
LIVENESS
CENTER TONE
CENTER	CTR
REAR•L	REARL
REAR•R	REARR

		STANDBY	ON
Ex. “SOUND” appears on the display	MAIN ROOM SUB ROOM
	MAIN ROOM	SUB ROOM TV/CATV/DBS	VCR1
	ON/OFF	ON/OFF POWER	POWER

window.

MAIN ROOM SUB ROOM

When you press the buttons listed above, the indication appears for 5 – 10 seconds for your confirmation.

41