Siemens WFXD5202UC manual Leveling Procedure, Transport Such When, Moving out, Inserting

Leveling Procedure

1.The appliance should now be in its final position, ready for leveling (moving the appliance after

leveling can make it unlevel again.)

Each foot of the appliance or pedestal must be placed firmly on the floor to prevent the washing 4. machine from wobbling.

Start with all four feet screwed in as far as possible, then back individual feet out as necessary to level the washer.

2.Use the bubble level to level the washer front to back and side to side (be sure the level fits between the edges of the washer, and is not elevated at mone end on a ridge on the surface of the washer.)

3.Adjust the leveling of the washer with the four height-adjustable feet. Level the washer as low as possible to heklp reduce vibration.

dCAUTION

TO AVOID RISK OF INJURIES-Take care when using the wrench.

q Loosen the lock nut1 (1 on the illustration) by turning it clockwise. Use the wrench provided (or a 5/8" - 16mm open end wrench). When you turn the lock nut, the 2footn ( the illustration) it is locked against will turn with it. This will extend the height of the foot.

q Turning the foot out				(clockwise)
will raise the corner of the
washer, turning the foot in
(counter-clockwise) will lower
the corner of the washer.
When	the corner		of	the	washer
is satisfactorily		raised		or
lowered, lock		the
height-adjustable feet				in	place	5.
by turning the lock nut
counter-clockwise until it locks
tightly	against	the	washer

housing.

iIt may be necessary to hold i the washer foot with a pair of pliers to keep it from turning while tightening the lock nut. It the foot does turn, it will change the height of the corner.

q After

making

preliminary

on

Transport,

such

as

when

adjustments, press

down

moving out

each corner of the washer to

make sure the unit does not

Before transporting

the

washing

wobble.

If it does

wobble,

machine:

lower the foot on that corner

-

Turn

off

the

water.

until

the

foot

touches

the

floor

-

Disconnect

the

washing machine

firmly.

from

the

power

outlet.

Use a bubble level (24"

or

less

in-

Dismantle the supply and drainage

length)

to check

the

leveling

status

hoses.

of the

appliance.

-

Install

the

transport

bolts.

q Lay the bubble level across thePreparing

and

inserting

the

unit

worktop

to check

the

level transport

bolts

from

side

to

side

and

from

front

to back.

q A center-located bubble

indicates the unit is leveled.

Otherwise,

repeat

the

leveling

procedure until the unit is

leveled.

Tip:

if the

bubble

is

closer to

one

end,

it

indicates

the high side of the unit. To

level the unit, either lower the

q

Remove

the

covers.

higher side or raise the lower

side.

q

Prepare

the

transport

bolts:

q After

leveling

the

unit

from

side

Loosen

the

screw

in

the

sleeve

until

the

end

of

the

screw is

level

to side, then

turn

the

level

so

with

the

end

of

the

sleeve.

that it lays on the worktop from

front to back to also

check theq

Insert and tighten all transport

level

in that

direction.

bolts.

Make

sure

that

the tab

on

the transportation

bolt

is

inserted

in the slot on the washing machine

back

panel.

Fine tune the leveling by placing a small load of laundry in the machine, starting it in spin cycle and then leveling the washer again.

If the test spin cycle is manually

stopped before its completion, then the door may remain locked for 10 seconds.

11