Advantech Safety INTRAC-305, Electrical, Do not Place in Normal Garbage or in a Fire

Page 10

SAFETY

INTRAC-305

1.SAFETY

WARNING

POSSIBLE LETHAL POTENTIALS EXIST WITHIN THIS EQUIPMENT

THE COVERS SHOULD NOT BE REMOVED EXCEPT BY QUALIFIED PERSONNEL.

SWITCH OFF POWER AND ISOLATE SUPPLY BEFORE REMOVING COVERS.

IF IT IS NECESSARY TO OPERATE THE EQUIPMENT WITH THE COVERS REMOVED FOR SERVICING PURPOSES ALL NECESSARY PRECAUTIONS SHOULD BE TAKEN TO PROTECT AGAINST ELECTRIC SHOCKS

ELECTRICAL

Fusing The standard unit is protected by a user replacable fuse in the live/phase power supply line.

Care should be taken to ensure that the power cable is correctly connected to the power source such that the live/phase connection of the INTRAC is connected to the live/phase terminal of the supply.

When replacing the fuse be sure to do so with one of the correct value and type.

The Dual Redundant power supply version is protected by separate board mounted fuses on each power supply. These are not user replaceable.

Earthing It is important that the electrical supply has a good and proper earth and that earth is connected through to the INTRAC-305 via the power cable.

Battery Disposal The processor board contains a Nickel Cadmium (NiCd) or Lithium battery. These elements are toxic. The battery should be disposed of according to national requirements.

DO NOT PLACE IN NORMAL GARBAGE OR IN A FIRE.

RF I/P Connector for IBR-L18Vdc may be present on the inner of the N-Type connector to power the LNB/BDC. This voltage can be removed by unplugging connector J41.

Emergency Stop There is a latching emergency stop switch on the INTRAC front panel. Pressing this switch will remove power from the antenna drive motors and the INTRAC will enter Standby mode. To restore drive the switch should be rotated clockwise (CW) and Auto Continue selected.

Page 10

INTRAC-305 MANUAL - Issue 3.2

© Advantech AMT Ltd

Image 10

Contents INTRAC-305 PrefacePreface PrefaceManual Sections INTRAC-305 Contents INTRAC-305 SubjectContents InstallationIntroducing the INTRAC-305 Introduction INTRAC-305Introduction Retro FittingIquick Start Guide INTRAC-305 Quick Start Guide Electrical SafetySafety INTRAC-305 Do not Place in Normal Garbage or in a FireMechanical SafetyEMC Page Specification & Options Specification & OptionsRequired Mechanical Characteristics of the Antenna System Specification Specification & Options INTRAC-305Do not Mount by Front Panel Lugs Alone Voltage Serial InterfacesINTRAC-305 Deliberately blank Operation Operating the INTRAC-305Front Panel Operation INTRAC-305 Menu StructureNext Field System SetupFunction EnterAlphabetical Index of Menus INTRAC-305 Home HomeStandby StandbyNEW Mode Goto Auto Continue New ModelHome NEW Mode Menu KEY MANUAL/STOWGoto Position Operation SearchGoto Satellite Auto Continue Auto NEW Model Remote Terminal Diagnostics Must be Function ConfigurationWhen IT is Required to Control the Intrac from Switched OFFBeacon Frequency Home Function Menu KEY 6 EnterEdit Satellite Table Config Menu KEY 6 X2 EnterHome Function Menu KEY 6 X2 Enter Soft Limits Drive in Manual Mode is not Inhibited bySoft Limits X2 Setup X2 Resolver SetupDiagnostics on / Diagnostics OFF Diagnostics OnBeacon Threshold System Setup Enter Home Function System Setup EnterContrast & Brightness Home Function System Setup Fine Tune senseFine Tune Offsets Azimuth true Elevation invStation CO-ORDINATES Date & Time Time Rate Correction AZ & EL Beamwidth Stow Setup Select Stow USE UsedFitted Options Home Function Models Enter Rapid Model GenerateModels Enter Home Function Models Menu KEY 6 Enter Program TrackModels Menu KEY 6 Enter Reserve Model Home Function ModelsINTRAC-305EDIT IESS-412 Edit Norad Buffer Edit Star Track Edit Satellite Table Clear Models Intrac IESS-412Show Alarms MoreREMOTE/LOCAL Normal Operation Alarms & Errors Alarms & ErrorsPrimary Alarms Alarm Outputs Alarms & Errors INTRAC-305Secondary Alarms Recovering from AlarmsPower Failure INTRAC-305 Alarms & ErrorsErrors IESS-412 DataDeliberately blank Technical Description Technical DescriptionTechnical Description INTRAC-305 Modes Auto normal operating mode Technical DescriptionWhere the satellite’s position is only roughly known search 72hrs, the beacon is still not producing a useful signal*Using either IESS-412 or Norad data. see Reserve Model High accuracy of the model the tracking is within 0.05dBManually or in search mode see below. To commence Enters Standby. The antenna can then be peaked usingManual mode or search mode see below before selecting During those scans and phase two of the search isUsing IESS-412 or Norad Data Than two places of decimals LMO value is given in the range -180to +180.XNDD60 EpochXNDT20 BstarAntenna Motion Limits Tracking Signal Axes PositionTechnical Description INTRAC-305 Installation InstallationInstallation INTRAC-305 Connections generalConnections Block Diagram InstallationRear Panel Layout Connector PIN Allocations Intractm 305 Resolvers ConnectorSignals to the Motor Drive Cabinet Motor ControlCommunication Ports Stp-Trk Inputs / Alarm outputsRemote Port Test Port 1 & 2 RS423 Test Port 1 & 2 RS422Data can be monitored during remote operation by using a Second PC connected to Test PortINTRAC-305 Installation Tracking Signal Input Tracking signal may be provided as a dc voltage from anOperational Checks Emergency Stop switch is releasedAppropriate drive command re-instated Manual OperationRemote Control Auto OperationFault Finding Fault FindingTo power up Fault Finding INTRAC-305Fault Symptoms Intrac doesn’t appearTWO Part Retaining PIN Switch consists of two normally closed N.C. contacts System Alarm indicator to illuminate and the Intrac toEnter Standby Mode Pressing the switch opens both sets of contacts. The switchNo Antenna Drive ExampleFault Finding INTRAC-305 Warranty Warranty & RepairWarranty & Repair Repair ServiceCustomer either by a Purchase Order or through a Repair AMT Limited will investigate the fault, determine the mostEffective repair technique and issue a repair cost estimate Contract