Advantech INTRAC-305 user manual Diagnostics on / Diagnostics OFF, Diagnostics On

Page 38

OPERATION

INTRAC-305

DIAGNOSTICS ON / DIAGNOSTICS OFF

Current Mode		Tracking
Control State		Local
Beac Freq		11.452000 GHz
Beac Level		-10.05 dB
El	Angle	25.37
Az	Angle	210.50
Pol	Angle	27.4
	Beacon Frequncy
	Edit Satellite Table
	Soft Limits
	Extended Azimuth Setup
	> Diagnostics On		<
	Diagnostics Off
	Beacon Threshold
Press EN to accept selection

Function

Standby

Home

Models

Test

Port-1

Diags

System

Setup

Next

Field

1

2

3

4

5

6

puts the antenna control system into STANDBY mode and skips to the HOME menu

skips to the Home (root) menu

skips to the Models menu

selects whether ‘Angles’ or ‘Diagnostics’ appear on Test Port 1

skips to the System Setup menu

moves the highlight box to the next field in the current menu

Path	HOME - FUNCTION - MENU KEY 6 (x5 for ON)
	(x6 for OFF) - ENTER
or	From Models or System Setup
	CONFIG - MENU KEY 6 (x5 or 6) - ENTER
Description	Diagnostics On & Off are used to route the INTRAC
	diagnostic data to the Remote Control port.
	Use Menu Key 6 to step the highlight bar to the ON or OFF
	line and press ENTER to set.
Note	This facility enables one PC to be used as both the remote
	control terminal and the diagnostics receiving terminal.
	However it cannot do both at the same time.
	WHEN IT IS REQUIRED TO CONTROL THE INTRAC FROM
	THE REMOTE TERMINAL DIAGNOSTICS MUST BE
	SWITCHED OFF.

Page 26

INTRAC-305 MANUAL - Issue 3.2

©2011 Advantech Wireless

Image 38

Contents INTRAC-305 PrefaceManual Sections PrefacePreface INTRAC-305 Contents INTRAC-305 SubjectContents InstallationIntroducing the INTRAC-305 Introduction INTRAC-305Introduction Retro FittingIquick Start Guide INTRAC-305 Quick Start Guide Electrical SafetySafety INTRAC-305 Do not Place in Normal Garbage or in a FireEMC SafetyMechanical Page Required Mechanical Characteristics of the Antenna System Specification & OptionsSpecification & Options Specification Specification & Options INTRAC-305Do not Mount by Front Panel Lugs Alone Voltage Serial InterfacesINTRAC-305 Deliberately blank Front Panel Operating the INTRAC-305Operation Operation INTRAC-305 Menu StructureNext Field System SetupFunction EnterAlphabetical Index of Menus INTRAC-305 Home HomeStandby StandbyNEW Mode Goto Auto Continue New ModelHome NEW Mode Menu KEY MANUAL/STOWGoto Position Operation SearchGoto Satellite Auto Continue Auto NEW Model Remote Terminal Diagnostics Must be Function ConfigurationWhen IT is Required to Control the Intrac from Switched OFFBeacon Frequency Home Function Menu KEY 6 EnterHome Function Menu KEY 6 X2 Enter Config Menu KEY 6 X2 EnterEdit Satellite Table Soft Limits Drive in Manual Mode is not Inhibited bySoft Limits X2 Setup X2 Resolver SetupDiagnostics on / Diagnostics OFF Diagnostics OnBeacon Threshold Contrast & Brightness Home Function System Setup EnterSystem Setup Enter Home Function System Setup Fine Tune senseFine Tune Offsets Azimuth true Elevation invStation CO-ORDINATES Date & Time Time Rate Correction AZ & EL Beamwidth Stow Setup Select Stow USE UsedFitted Options Models Enter Rapid Model GenerateHome Function Models Enter Models Menu KEY 6 Enter Program TrackHome Function Models Menu KEY 6 Enter Reserve Model Home Function ModelsINTRAC-305EDIT IESS-412 Edit Norad Buffer Edit Star Track Edit Satellite Table Clear Models Intrac IESS-412Show Alarms MoreREMOTE/LOCAL Normal Operation Primary Alarms Alarms & ErrorsAlarms & Errors Alarm Outputs Alarms & Errors INTRAC-305Secondary Alarms Recovering from AlarmsPower Failure INTRAC-305 Alarms & ErrorsErrors IESS-412 DataDeliberately blank Technical Description Technical DescriptionTechnical Description INTRAC-305 Modes Auto normal operating mode Technical DescriptionWhere the satellite’s position is only roughly known search 72hrs, the beacon is still not producing a useful signal*Using either IESS-412 or Norad data. see Reserve Model High accuracy of the model the tracking is within 0.05dBManually or in search mode see below. To commence Enters Standby. The antenna can then be peaked usingManual mode or search mode see below before selecting During those scans and phase two of the search isUsing IESS-412 or Norad Data Than two places of decimals LMO value is given in the range -180to +180.XNDD60 EpochXNDT20 BstarAntenna Motion Limits Tracking Signal Axes PositionTechnical Description INTRAC-305 Installation InstallationInstallation INTRAC-305 Connections generalRear Panel Layout InstallationConnections Block Diagram Connector PIN Allocations Intractm 305 Resolvers ConnectorSignals to the Motor Drive Cabinet Motor ControlRemote Port Stp-Trk Inputs / Alarm outputsCommunication Ports Test Port 1 & 2 RS423 Test Port 1 & 2 RS422Data can be monitored during remote operation by using a Second PC connected to Test PortINTRAC-305 Installation Tracking Signal Input Tracking signal may be provided as a dc voltage from anOperational Checks Emergency Stop switch is releasedAppropriate drive command re-instated Manual OperationRemote Control Auto OperationFault Finding Fault FindingTo power up Fault Finding INTRAC-305Fault Symptoms Intrac doesn’t appearTWO Part Retaining PIN Switch consists of two normally closed N.C. contacts System Alarm indicator to illuminate and the Intrac toEnter Standby Mode Pressing the switch opens both sets of contacts. The switchNo Antenna Drive ExampleFault Finding INTRAC-305 Warranty Warranty & RepairWarranty & Repair Repair ServiceCustomer either by a Purchase Order or through a Repair AMT Limited will investigate the fault, determine the mostEffective repair technique and issue a repair cost estimate Contract