Advantech INTRAC-305 user manual Alphabetical Index of Menus

Page 22

OPERATION

INTRAC-305

On the next page is an alphabetical index of the menus to assist in the quick location of a specific function.

ALPHABETICAL INDEX OF MENUS

Alarms	48
Auto Continue	21
Auto New Model	22
Az & El Beamwidth	36
Beacon Frequency	24
Beacon Threshold	29
Beamwidth Az & El	36
Brightness & Contrast	30
Clear Models	47
Configuration	23
Contrast & Brightness	30
Date & Time Setting	34
Diagnostics On/Off	28
Edit IESS-412	43
Edit NORAD	44
Edit Satellite Table	25
Edit Star Track	45
Fine Tune Offsets	32
Fine Tune Sense	31
Fitted Options	39
Function	23
Goto Position	18

Page 10

INTRAC-305 MANUAL - Issue 3.2

©2011 Advantech Wireless

Image 22

Contents INTRAC-305 PrefacePreface PrefaceManual Sections INTRAC-305 Contents INTRAC-305 SubjectContents InstallationIntroducing the INTRAC-305 Introduction INTRAC-305Introduction Retro FittingIquick Start Guide INTRAC-305 Quick Start Guide Electrical SafetySafety INTRAC-305 Do not Place in Normal Garbage or in a FireMechanical SafetyEMC Page Specification & Options Specification & OptionsRequired Mechanical Characteristics of the Antenna System Specification Specification & Options INTRAC-305Do not Mount by Front Panel Lugs Alone Voltage Serial InterfacesINTRAC-305 Deliberately blank Operation Operating the INTRAC-305Front Panel Operation INTRAC-305 Menu StructureNext Field System SetupFunction EnterAlphabetical Index of Menus INTRAC-305 Home HomeStandby StandbyNEW Mode Goto Auto Continue New ModelHome NEW Mode Menu KEY MANUAL/STOWGoto Position Operation SearchGoto Satellite Auto Continue Auto NEW Model Remote Terminal Diagnostics Must be Function ConfigurationWhen IT is Required to Control the Intrac from Switched OFFBeacon Frequency Home Function Menu KEY 6 EnterEdit Satellite Table Config Menu KEY 6 X2 EnterHome Function Menu KEY 6 X2 Enter Soft Limits Drive in Manual Mode is not Inhibited bySoft Limits X2 Setup X2 Resolver SetupDiagnostics on / Diagnostics OFF Diagnostics OnBeacon Threshold System Setup Enter Home Function System Setup EnterContrast & Brightness Home Function System Setup Fine Tune senseFine Tune Offsets Azimuth true Elevation invStation CO-ORDINATES Date & Time Time Rate Correction AZ & EL Beamwidth Stow Setup Select Stow USE UsedFitted Options Home Function Models Enter Rapid Model GenerateModels Enter Home Function Models Menu KEY 6 Enter Program TrackModels Menu KEY 6 Enter Reserve Model Home Function ModelsINTRAC-305EDIT IESS-412 Edit Norad Buffer Edit Star Track Edit Satellite Table Clear Models Intrac IESS-412Show Alarms MoreREMOTE/LOCAL Normal Operation Alarms & Errors Alarms & ErrorsPrimary Alarms Alarm Outputs Alarms & Errors INTRAC-305Secondary Alarms Recovering from AlarmsPower Failure INTRAC-305 Alarms & ErrorsErrors IESS-412 DataDeliberately blank Technical Description Technical DescriptionTechnical Description INTRAC-305 Modes Auto normal operating mode Technical DescriptionWhere the satellite’s position is only roughly known search 72hrs, the beacon is still not producing a useful signal*Using either IESS-412 or Norad data. see Reserve Model High accuracy of the model the tracking is within 0.05dBManually or in search mode see below. To commence Enters Standby. The antenna can then be peaked usingManual mode or search mode see below before selecting During those scans and phase two of the search isUsing IESS-412 or Norad Data Than two places of decimals LMO value is given in the range -180to +180.XNDD60 EpochXNDT20 BstarAntenna Motion Limits Tracking Signal Axes PositionTechnical Description INTRAC-305 Installation InstallationInstallation INTRAC-305 Connections generalConnections Block Diagram InstallationRear Panel Layout Connector PIN Allocations Intractm 305 Resolvers ConnectorSignals to the Motor Drive Cabinet Motor ControlCommunication Ports Stp-Trk Inputs / Alarm outputsRemote Port Test Port 1 & 2 RS423 Test Port 1 & 2 RS422Data can be monitored during remote operation by using a Second PC connected to Test PortINTRAC-305 Installation Tracking Signal Input Tracking signal may be provided as a dc voltage from anOperational Checks Emergency Stop switch is releasedAppropriate drive command re-instated Manual OperationRemote Control Auto OperationFault Finding Fault FindingTo power up Fault Finding INTRAC-305Fault Symptoms Intrac doesn’t appearTWO Part Retaining PIN Switch consists of two normally closed N.C. contacts System Alarm indicator to illuminate and the Intrac toEnter Standby Mode Pressing the switch opens both sets of contacts. The switchNo Antenna Drive ExampleFault Finding INTRAC-305 Warranty Warranty & RepairWarranty & Repair Repair ServiceCustomer either by a Purchase Order or through a Repair AMT Limited will investigate the fault, determine the mostEffective repair technique and issue a repair cost estimate Contract