Advantech INTRAC-305 user manual Installation

Page 77

6

INTRAC-305

INSTALLATION

6.INSTALLATION

Introduction

The INTRAC-305 Intelligent Tracking Antenna Controller is a

 

direct physical replacement for the Andrew APC300 Antenna

 

Steptrack Controller. All that is required for the installation is

 

to remove the APC300 and replace it with the INTRAC-305

 

and then set-up the INTRAC-305 for the antenna system.

 

This section provides information on connections and set-up.

 

The INTRAC-305 requires that certain parameters be set and

 

certain information be input before it will be able to function

 

correctly. Some of this information can be obtained from the

 

APC300 but some will need to be obtained from other

 

sources. The chart below gives the parameters required by

 

the INTRAC-305. Four items under “Fitted Options” should

 

be set to “Not Fitted” (as indicated) as they are not applicable

 

to APC300 systems. For more information on these settings

 

see section 3-Operation of this manual.

 

 

Electrical supply voltage setting

________ volts

 

Az, El & Pol (if fitted) angles

Az ____° El ____° Pol ___°

Note

Once the pointing angles are noted ensure that the antenna is not

 

moved.

 

 

 

 

Beacon Level

________ dB

 

Beacon Frequency

________ MHz / GHz

 

Is 18 volts dc LNB supply required on the beacon receiver input N-

 

type connector. (Only relevant if the SPL IBR-L option is fitted))

Fitted Options

Beacon Receiver (IBR-L)

Fitted / Not Fitted

 

Pol Sel A/B

set to

Not Fitted

 

Polarization

Fitted / Not Fitted

 

Mount Type

Az/El or Hrang/Dcl

 

Resolver Type.........…… x1 or x2

(normally x2 for std Andrew RESK*-300)

 

Extended Az

set to

Not Fitted

 

Geared Pol

set to

Not Fitted

 

Simax Drive

set to Fitted

 

Inv Beacon Lock

set to

Not Fitted

System Setup

Resolver Sense

Az: true/inv, El: true/inv, Pol :true/inv

Beamwidth

Azimuth:______

Elevation: _______

Soft Limits

Az right: ______

Az left: _________

 

El up: ________

El down: ________

 

Pol cw: _______

Pol ccw: ________

Stow Setup - Prelim Position

Az: ______

El: ______

Final Position

Az: ______

El: ______

Stow Use

- Prelim Position

Az

Used / Not Used

 

 

 

El

Used / Not Used

Final Position

Az

Used / Not Used

 

 

 

El

Used / Not Used

Beacon Threshold

_______dB

 

Station Co-ordinates

Lat _____ Long _____ Ht in Km _____

Record any stored satellites

© 2011 Advantech Wireless

INTRAC-305 MANUAL - Issue 3.2

Page 65

Image 77
Contents Preface INTRAC-305Manual Sections PrefacePreface INTRAC-305 Subject Contents INTRAC-305Installation ContentsIntroduction INTRAC-305 Introducing the INTRAC-305Retro Fitting IntroductionIquick Start Guide INTRAC-305 Quick Start Guide Safety INTRAC-305 SafetyElectrical Do not Place in Normal Garbage or in a FireEMC SafetyMechanical Page Required Mechanical Characteristics of the Antenna System Specification & OptionsSpecification & Options Specification & Options INTRAC-305 SpecificationDo not Mount by Front Panel Lugs Alone Serial Interfaces VoltageINTRAC-305 Deliberately blank Front Panel Operating the INTRAC-305Operation Menu Structure Operation INTRAC-305Function System SetupNext Field EnterAlphabetical Index of Menus INTRAC-305 Home HomeStandby StandbyGoto Auto Continue New Model NEW ModeMANUAL/STOW Home NEW Mode Menu KEYGoto Position Search OperationGoto Satellite Auto Continue Auto NEW Model When IT is Required to Control the Intrac from Function ConfigurationRemote Terminal Diagnostics Must be Switched OFFHome Function Menu KEY 6 Enter Beacon FrequencyHome Function Menu KEY 6 X2 Enter Config Menu KEY 6 X2 EnterEdit Satellite Table Soft Limits Drive in Manual Mode is not Inhibited bySoft Limits X2 Resolver Setup X2 SetupDiagnostics On Diagnostics on / Diagnostics OFFBeacon Threshold Contrast & Brightness Home Function System Setup EnterSystem Setup Enter Fine Tune sense Home Function System SetupAzimuth true Elevation inv Fine Tune OffsetsStation CO-ORDINATES Date & Time Time Rate Correction AZ & EL Beamwidth Stow Setup Used Select Stow USEFitted Options Models Enter Rapid Model GenerateHome Function Models Enter Models Menu KEY 6 Enter Program TrackHome Function Models Menu KEY 6 Enter Home Function Models Reserve ModelINTRAC-305EDIT IESS-412 Edit Norad Buffer Edit Star Track Edit Satellite Table Intrac IESS-412 Clear ModelsMore Show AlarmsREMOTE/LOCAL Normal Operation Primary Alarms Alarms & ErrorsAlarms & Errors Secondary Alarms Alarms & Errors INTRAC-305Alarm Outputs Recovering from AlarmsErrors INTRAC-305 Alarms & ErrorsPower Failure IESS-412 DataDeliberately blank Technical Description Technical DescriptionTechnical Description INTRAC-305 Modes Technical Description Auto normal operating modeUsing either IESS-412 or Norad data. see Reserve Model 72hrs, the beacon is still not producing a useful signal*Where the satellite’s position is only roughly known search High accuracy of the model the tracking is within 0.05dBManual mode or search mode see below before selecting Enters Standby. The antenna can then be peaked usingManually or in search mode see below. To commence During those scans and phase two of the search isUsing IESS-412 or Norad Data LMO value is given in the range -180to +180. Than two places of decimalsXNDT20 EpochXNDD60 BstarAntenna Motion Limits Axes Position Tracking SignalTechnical Description INTRAC-305 Installation InstallationConnections general Installation INTRAC-305Rear Panel Layout InstallationConnections Block Diagram Intractm 305 Resolvers Connector Connector PIN AllocationsMotor Control Signals to the Motor Drive CabinetRemote Port Stp-Trk Inputs / Alarm outputsCommunication Ports Test Port 1 & 2 RS422 Test Port 1 & 2 RS423Second PC connected to Test Port Data can be monitored during remote operation by using aINTRAC-305 Installation Tracking signal may be provided as a dc voltage from an Tracking Signal InputAppropriate drive command re-instated Emergency Stop switch is releasedOperational Checks Manual OperationAuto Operation Remote ControlFault Finding Fault FindingFault Symptoms Fault Finding INTRAC-305To power up Intrac doesn’t appearTWO Part Retaining PIN Enter Standby Mode System Alarm indicator to illuminate and the Intrac toSwitch consists of two normally closed N.C. contacts Pressing the switch opens both sets of contacts. The switchExample No Antenna DriveFault Finding INTRAC-305 Warranty & Repair Warranty & RepairWarranty Repair ServiceEffective repair technique and issue a repair cost estimate AMT Limited will investigate the fault, determine the mostCustomer either by a Purchase Order or through a Repair Contract