Emerson 00825-0100-4716 manual Rosemount 3095 MultiVariable, Quick Installation Guide

Page 1

Quick Installation Guide

00825-0100-4716, Rev DA October 2009

Rosemount 3095 MultiVariable

Rosemount 3095 MultiVariable™ Mass Flow Transmitter with HART® or FOUNDATION™

Fieldbus Protocol

Rosemount 3095MF Series Flowmeter Transmitter

Start

Step 1: Mount the Transmitter

Step 2: Transmitter Installation

Step 3: Software Installation

Step 4: Connect the Wiring and Power Up (HART or Fieldbus)

Step 5: Configure the Transmitter (HART or Fieldbus)

Step 6: Trim the Transmitter

Product Certifications

End

www.rosemount.com

¢00825-0100-4716/¤

Image 1

Contents Rosemount 3095 MultiVariable Quick Installation GuideFieldbus Protocol Rosemount 3095MF Series Flowmeter Transmitter ¢00825-0100-4716/¤Process leaks may cause harm or result in death Explosions could result in death or serious injuryElectrical shock can result in death or serious injury IMPORTANT NOTICERTD Connector TRANSMITTER EXPLODED VIEWTerminal Block HART O-ring Cover Certification Label Electronics Board Nameplate Module O-ringLiquid Flow Applications STEP 1 MOUNT THE TRANSMITTERGas Flow Applications Steam Flow ApplicationsConsider Housing Rotation STEP 2 TRANSMITTER INSTALLATIONField Installation Figure 2. Alarm Jumper Location STEP 2 CONTINUEDFigure 3. Armored Shielded RTD Cable Cable Gland Black Cable Connector/ RTD Connector Cable Adapter 1/2-14 NPT Black Cable ConnectorFigure 4. Shielded RTD Cable Figure 5. ATEX/IECEx Flameproof RTD CableFigure 6. Common Transmitter Assemblies Bolting ConsiderationsFlange Adapter O-rings with Flange AdaptersO-ring PTFE Based3095 Engineering Assistant EA for HART Software Installation STEP 3 SOFTWARE INSTALLATION3095 Engineering Assistant EA for FOUNDATION Fieldbus Installing the HART ModemSTEP 3 CONTINUED 3. Select Hart Modem24 Vdc Supply Current RL≥ 250Ω Meter STEP 4 CONNECT WIRING AND POWER UP HARTPower Supply STEP 4 CONNECT WIRING AND POWER UP FIELDBUSPower Conditioner Shield Wire GroundSetting the Loop to Manual STEP 5 CONFIGURE THE TRANSMITTER HARTSend the Configuration to the Transmitter Basic Configuration ParametersRosemount 3095 MultiVariable To configure the AI Block STEP 5 CONFIGURE THE TRANSMITTER FIELDBUSAI Block configuration parameters Using the Foundation Fieldbus AI Block Using the Field CommunicatorUsing the Foundation Fieldbus Host System STEP 6 TRIM THE TRANSMITTERApproved Manufacturing Locations PRODUCT CERTIFICATIONS Rosemount 3095 with HARTEuropean Directive Information Rosemount 3095 HART Hazardous Locations CertificationsEuropean Certifications Canadian Standards Association CSASpecial Conditions for Safe Use IECEx Certifications HART INMETRO Certifications Conditions of CertificationSpecial conditions for safe use China NEPSI CertificationsL i ≈ Maximum Temperature of Combinations of Certifications Rosemount 3095 with FieldbusATEX Directive 94/9/EC European Pressure Equipment Directive PED 97/23/ECNorth American Certifications Rosemount 3095 Fieldbus Hazardous Locations CertificationsFM Approvals Canadian Standards Association CSARosemount 3095 MultiVariable IECEx Certifications Fieldbus Rosemount 3095 MultiVariable Quick Installation GuideCombinations of Certifications Rosemount 3095 MultiVariable Quick Installation GuideRosemount 3095 MultiVariable Quick Installation GuideRosemount 3095 MultiVariable Quick Installation GuideRosemount 3095 MultiVariable Quick Installation Guide