Belkin 8000I Northstar 8000i Video Interface, Northstar 8000i C-MAP Chart License Key

Page 25

Location Guide

Locate the keypad relative to the screen it is controlling. The keypad does not require external power

Mounting

Select an area that has easy access in order to control the 8000i. Make sure the panel it is being mounted into is flat, to ensure a watertight seal

6.10Northstar 8000i Video Interface

USB Video capture device NS004745

Description

Video to USB converter

Functionality

Interfaces composite or S-Video feeds to a 8000i processor. Composite or S-Video can be from a security camera or a an entertainment source. It is converted to a USB feed which connects to a 8000i possessor or USB hub. The feed is then displayed on the 8000i processor it is connected to. The video is not networked. It is only visible on the local processor. The device can use NTSC PAL or SECAM. Select which source you use from with in the 8000i software.

NOTE: Only one video capture device can be used per processor

Other parts required

Third party video feed. If using audio; connect the audio feed of the device to NS004802 audio cable which then connects to the Aux connector of the processor

Location Guide

Connect to a 8000i processor. Don't use a USB cable longer than 16.5 ft (5 m). Pay special attention to the video and audio cable runs. Refer to wiring guide (see "Wiring Guidelines" page 37)

6.11Northstar 8000i C-MAP Chart License Key

C-Map Chart License Key

Description

C-Map Chart License Key

Functionality

Holds the license information of the purchased charts.

Northstar 8000i System - 12" Display Processor Installation Manual

25

Image 25

Contents

Northstar Preface Important Safety InformationPlease read carefully before use Ft 0.5 m Disclaimer WarrantyContents Example System Layouts Maintenance Check the 12 inch Display Processor parts Introducing the Northstar 8000i SystemChart License Key NS004820 Page PPI Find your way around the 12 inch Display ProcessorRGB Network Master Unit Installation Sequence Summary Guidelines 8000i System InstallationDescription Northstar 8000i 12 inch Display ProcessorPlace in 8000i System Optional PartsNorthstar 8000i Black Box Processor Power requirementsLocation Guide MountingNorthstar 8000i 15 inch Monitor Other parts required Northstar 8000i Network Radar Power requirements Voltage Fuse DrawFunctions Northstar 8000i 8 Port Network Linker Northstar 8000i 4 Port USB Hub Functionality Northstar 8000i 1 kW Network SounderNorthstar 8000i DVD-CD Player Northstar 8000i Remote Keypad Northstar 8000i Video Interface Northstar 8000i C-MAP Chart License KeyNorthstar GPS Antenna NS004743 Autopilot Other ComponentsAudio Heading SensorMounting and Calibration GLL NMEA-0183 DataGSA Mass Storage Devices Network Camera Human Interface DevicesDescription Place in 8000i System Other Functions Location GuideChoosing the best mounting location Mounting the 8000i 12 inch Display ProcessorViewing Angle Page Page Wiring Guidelines Power Northstar 8000i Black Box 8000i System Power requirementsGPS Port Utility Port External Wake Up and Remote Power OnConnect this to the Light Green wire on Page Nmea Multiplexer Noland NM42 NmeaWiring Connect the following External AlarmPage USB Auxiliary port Network RGB portPage Field Terminated Network Cable Brown White/Brown Blue White/Green White/Blue Terminating a Northstar 8000i RJ45 Field Kit Before crimp After crimp Example System Layouts 8000i Chart Plotter8000i Plotter Sounder NS004743 Northstar GPS Antenna Entertainment Northstar 8000i Processor Full System Northstar Black Box Processor NS004730 Adjust the brightness on a 12 inch Display Processor Northstar 8000i Initial SetupTo adjust the backlight brightness Turn on the 12 inch Display ProcessorTo set the master Set the network master unitInstall Charts interface Install the chart dataTo install chart collections To install all collectionsTurn off the 12 inch Display Processor To select the time format Set the system preferencesTo select your time zone To turn the beeps on or offTo turn the backlight on or off To change the transducer depthChange the transducer depth Turn the keypad backlight on or offSpecify your vessel statistics To show or hide the top control barTo specify your vessel statistics Set the location of the media libraryTo select Nmea Output sentences Set Nmea OutputCalibrate the touch screen Set Nmea Baud RateTo calibrate the touch screen Set the device processor nameSet the units Set the screen resolutionTo select the large scale distance units To select the volume units for liquidsTo select the small scale distance units To set up the radar before using it To select the temperature unitsSelect the temperature units Set up the radar before using it for the first timeChange the radar startup mode To change the radar startup modeChange the radar range offset trigger delay To change the radar bearing alignment To change the radar range offsetTo change the parking angle Change the radar bearing alignmentTo change the water temperature averaging time To change the offset for the water temperatureSounder To change the speed offsetTo create an instrument panel InstrumentsChange the sounders speed filter Create an instrument panelTo resize an instrument To add a new instrumentTo rename an instrument panel Resize an instrumentDelete an instrument panel To delete an instrument panelTechnical support, service and repairs MaintenanceRestore settings and information RestoreRestore processor software To restore the system processorUpgrading the 8000i system There two types of upgrade for a 8000i processorInstall a system image upgrade Install a software patch to multi processor systemSystem image upgrade Software patch multi-processor system MasterThirty minutes System will then restart automatically Display SpecificationsUnited States Europe Northstar