Belkin 8000I To show or hide the top control bar, Specify your vessel statistics

Page 69

Alternatively:

1.If you are using a 12" Display Processor, press the Power key briefly to display a list of options, then use the directional arrows to select Key Backlight. Use the rotary knob to change the setting.

10.6.6Show/hide the top control bar

You can choose whether to show or hide the top control bar along the top of the screen. (The buttons in the top control bar duplicate the keys.)

If you change this setting, the 8000i will restart automatically.

To show or hide the top control bar:

1.Select Display, then select Setup from the control panel.

2.Select + Installation to display a list of installation specification options.

3.The Display Top Control Bar check box shows the current setting.

4.Select the check box if you want to toggle to the other setting. The 8000i restarts automatically and the new setting stays until you change it again.

5.When you are finished, select – Installation.

10.7Specify your vessel statistics

The following important information about your vessel should already be set up as part of the installation process, but you can change any of this if necessary.

If you do not enter an accurate draft AND an accurate safe depth, the "Depth Below Keel"

alarm will not work correctly and your vessel is at risk of grounding. To calculate the safe depth, use the draft of your vessel and then add a safety margin.

To specify your vessel statistics:

1.Select Display.

2.Select Setup from the control panel.

3.Select + Vessel Statistics to display the current settings for the:

Cruising Speed Draft

Safe Depth (vessel draft, plus a safety margin)

4.Select EDIT next to the item that you want to change, then use the online keyboard to enter the new setting. Press OK to return to the vessel statistics options.

5.The new setting is applied immediately and stays until you change it again. If you want to change another setting, repeat the previous step.

6.When you are finished, select – Vessel Statistics.

10.8Set the location of the media library

You must enter the location of the media library so that the 8000i can find your stored music and videos.

To set the location of the media library:

1. Select Display.

Northstar 8000i System - 12" Display Processor Installation Manual

69

Image 69

Contents Northstar Important Safety Information PrefacePlease read carefully before use Ft 0.5 m Disclaimer WarrantyContents Example System Layouts Maintenance Check the 12 inch Display Processor parts Introducing the Northstar 8000i SystemChart License Key NS004820 Page PPI Find your way around the 12 inch Display ProcessorRGB Network Master Unit Installation Sequence Summary Guidelines 8000i System InstallationDescription Northstar 8000i 12 inch Display ProcessorPlace in 8000i System Optional PartsNorthstar 8000i Black Box Processor Power requirementsLocation Guide MountingNorthstar 8000i 15 inch Monitor Other parts required Power requirements Voltage Fuse Draw Northstar 8000i Network RadarFunctions Northstar 8000i 8 Port Network Linker Northstar 8000i 4 Port USB Hub Functionality Northstar 8000i 1 kW Network SounderNorthstar 8000i DVD-CD Player Northstar 8000i Remote Keypad Northstar 8000i Video Interface Northstar 8000i C-MAP Chart License KeyNorthstar GPS Antenna NS004743 Autopilot Other ComponentsHeading Sensor AudioMounting and Calibration GLL NMEA-0183 DataGSA Mass Storage Devices Network Camera Human Interface DevicesDescription Place in 8000i System Other Functions Location GuideChoosing the best mounting location Mounting the 8000i 12 inch Display ProcessorViewing Angle Page Page Wiring Guidelines Power Northstar 8000i Black Box 8000i System Power requirementsGPS Port Utility Port External Wake Up and Remote Power OnConnect this to the Light Green wire on Page Nmea Multiplexer Noland NM42 NmeaWiring Connect the following External AlarmPage USB Auxiliary port Network RGB portPage Field Terminated Network Cable Brown White/Brown Blue White/Green White/Blue Terminating a Northstar 8000i RJ45 Field Kit Before crimp After crimp Example System Layouts 8000i Chart Plotter8000i Plotter Sounder NS004743 Northstar GPS Antenna Entertainment Northstar 8000i Processor Full System Northstar Black Box Processor NS004730 Adjust the brightness on a 12 inch Display Processor Northstar 8000i Initial SetupTo adjust the backlight brightness Turn on the 12 inch Display ProcessorTo set the master Set the network master unitInstall Charts interface Install the chart dataTo install chart collections To install all collectionsTurn off the 12 inch Display Processor To select the time format Set the system preferencesTo select your time zone To turn the beeps on or offTo turn the backlight on or off To change the transducer depthChange the transducer depth Turn the keypad backlight on or offSpecify your vessel statistics To show or hide the top control barTo specify your vessel statistics Set the location of the media libraryTo select Nmea Output sentences Set Nmea OutputCalibrate the touch screen Set Nmea Baud RateTo calibrate the touch screen Set the device processor nameSet the units Set the screen resolutionTo select the volume units for liquids To select the large scale distance unitsTo select the small scale distance units To set up the radar before using it To select the temperature unitsSelect the temperature units Set up the radar before using it for the first timeTo change the radar startup mode Change the radar startup modeChange the radar range offset trigger delay To change the radar bearing alignment To change the radar range offsetTo change the parking angle Change the radar bearing alignmentTo change the water temperature averaging time To change the offset for the water temperatureSounder To change the speed offsetTo create an instrument panel InstrumentsChange the sounders speed filter Create an instrument panelTo resize an instrument To add a new instrumentTo rename an instrument panel Resize an instrumentDelete an instrument panel To delete an instrument panelTechnical support, service and repairs MaintenanceRestore settings and information RestoreRestore processor software To restore the system processorUpgrading the 8000i system There two types of upgrade for a 8000i processorInstall a system image upgrade Install a software patch to multi processor systemSystem image upgrade Software patch multi-processor system MasterThirty minutes System will then restart automatically Display SpecificationsUnited States Europe Northstar