Belkin 8000I installation manual Power

Page 38

8.1Power

Before starting the installation, be sure to turn electrical power off. If power is left on or turned on during the installation, fire, electrical shock, or other serious injury may occur. Be sure that the voltage of the power supply is compatible with the 8000i’s voltage rating of 12 V DC or 24 V DC. (10 V DC - 35 V DC max range)

Connecting to the wrong power supply can cause fire or damage to the equipment.

Be sure to ground the equipment to prevent electrical shock and mutual interference. Be sure to use the fuse in the supplied power cable. Not using a fuse can cause fire or damage to the 8000i.

All 8000i units are shipped with a 6 ft (2 m) power cable. This can be extended using the following guidelines

ƒ

ƒ

for a cable length up to 15 ft (5 m), use 14-gauge wire or heavier

for a cable length from 15 ft (5 m) to 30 ft (10 m), use 12-gauge wire or heavier

If you lengthen the power cable, use an external fuse at the battery end as an added safety precaution. The fuse size should be chosen to be appropriate for the size of the smallest conductor in the circuit. See the NMEA or American Boating and Yachting Counsel specifications to find the correct fuse for your wiring.

For the best protection from noise, connect the power wiring directly to the battery or dedicated electronics bus. The brown ground wire should be connected directly to ship’s ground. The power cable has an inline fuse on the positive and negative side to protect the vessel’s wiring, and prevent electrical fires and damage to the unit. If you shorten or lengthen this cable, be sure to keep the inline fuse intact (or provide circuit protection).

Spare in-line fuses are standard automotive type and are not supplied with the unit and should be purchased locally to avoid loss of function.

The 8000i can operate on voltages ranging from 10 V DC to 35 V DC. All Northstar 8000i components except the use the same 3 Pin power connector and cable as below.

NOTE: Make sure the correct fuse is used

Northstar 8000i System - 12" Display Processor Installation Manual

38

Image 38
Contents Northstar Please read carefully before use Important Safety InformationPreface Ft 0.5 m Warranty DisclaimerContents Example System Layouts Maintenance Introducing the Northstar 8000i System Check the 12 inch Display Processor partsChart License Key NS004820 Page Find your way around the 12 inch Display Processor PPIRGB Network Master Unit 8000i System Installation Installation Sequence Summary GuidelinesPlace in 8000i System Northstar 8000i 12 inch Display ProcessorDescription Optional PartsLocation Guide Power requirementsNorthstar 8000i Black Box Processor MountingNorthstar 8000i 15 inch Monitor Other parts required Functions Power requirements Voltage Fuse DrawNorthstar 8000i Network Radar Northstar 8000i 8 Port Network Linker Northstar 8000i 4 Port USB Hub Northstar 8000i 1 kW Network Sounder FunctionalityNorthstar 8000i DVD-CD Player Northstar 8000i Remote Keypad Northstar 8000i C-MAP Chart License Key Northstar 8000i Video InterfaceNorthstar GPS Antenna NS004743 Other Components AutopilotMounting and Calibration Heading SensorAudio NMEA-0183 Data GLLGSA Mass Storage Devices Description Place in 8000i System Human Interface DevicesNetwork Camera Other Functions Location GuideMounting the 8000i 12 inch Display Processor Choosing the best mounting locationViewing Angle Page Page Wiring Guidelines Power 8000i System Power requirements Northstar 8000i Black BoxGPS Port External Wake Up and Remote Power On Utility PortConnect this to the Light Green wire on Page Nmea Nmea Multiplexer Noland NM42Wiring External Alarm Connect the followingPage USB Auxiliary port RGB port NetworkPage Field Terminated Network Cable Brown White/Brown Blue White/Green White/Blue Terminating a Northstar 8000i RJ45 Field Kit Before crimp After crimp 8000i Chart Plotter Example System Layouts8000i Plotter Sounder NS004743 Northstar GPS Antenna Entertainment Northstar 8000i Processor Full System Northstar Black Box Processor NS004730 To adjust the backlight brightness Northstar 8000i Initial SetupAdjust the brightness on a 12 inch Display Processor Turn on the 12 inch Display ProcessorSet the network master unit To set the masterTo install chart collections Install the chart dataInstall Charts interface To install all collectionsTurn off the 12 inch Display Processor To select your time zone Set the system preferencesTo select the time format To turn the beeps on or offChange the transducer depth To change the transducer depthTo turn the backlight on or off Turn the keypad backlight on or offTo specify your vessel statistics To show or hide the top control barSpecify your vessel statistics Set the location of the media librarySet Nmea Output To select Nmea Output sentencesTo calibrate the touch screen Set Nmea Baud RateCalibrate the touch screen Set the device processor nameSet the screen resolution Set the unitsTo select the small scale distance units To select the volume units for liquidsTo select the large scale distance units Select the temperature units To select the temperature unitsTo set up the radar before using it Set up the radar before using it for the first timeChange the radar range offset trigger delay To change the radar startup modeChange the radar startup mode To change the parking angle To change the radar range offsetTo change the radar bearing alignment Change the radar bearing alignmentSounder To change the offset for the water temperatureTo change the water temperature averaging time To change the speed offsetChange the sounders speed filter InstrumentsTo create an instrument panel Create an instrument panelTo rename an instrument panel To add a new instrumentTo resize an instrument Resize an instrumentTo delete an instrument panel Delete an instrument panelMaintenance Technical support, service and repairsRestore processor software RestoreRestore settings and information To restore the system processorThere two types of upgrade for a 8000i processor Upgrading the 8000i systemSystem image upgrade Install a software patch to multi processor systemInstall a system image upgrade Software patch multi-processor system MasterThirty minutes System will then restart automatically Specifications DisplayUnited States Europe Northstar