Belkin 8000I installation manual Before crimp After crimp

Page 55

9.Hold the arranged wires between your thumb and index finger so that the wires are close together and flatten

10.Once the wires are in the right order and flat cut them off to a length of ½" (12.7 mm) (see diagram above)

11.Insert the wires in the RJ 45 connector (NOTE Make sure the connector is positioned tang down)

12.Make sure the wires are pushed the very end of the connector and that some of the outer sleeve is inside the connector (see diagram below

13.Using an RJ45 crimp tool and following the instructions of the tool terminate the connection

Before crimp

After crimp

A

B

C

Crimp tool. The crimp tools jaw presses the gold plated contacts down so they pierce through the insulation of all eight wires to make contact with the copper conductor

Network cable

Make sure sheath is pushed well inside the connector

14.Cut any spare shield wire close to the plug

16.Slide the gasket, body and locking nut over the RJ45 connector slide

17.Slide the sealing nut and seal towards the body and screw together.

Northstar 8000i System - 12" Display Processor Installation Manual

55

Image 55

Contents Northstar Preface Important Safety InformationPlease read carefully before use Ft 0.5 m Disclaimer WarrantyContents Example System Layouts Maintenance Check the 12 inch Display Processor parts Introducing the Northstar 8000i SystemChart License Key NS004820 Page PPI Find your way around the 12 inch Display ProcessorRGB Network Master Unit Installation Sequence Summary Guidelines 8000i System InstallationOptional Parts Northstar 8000i 12 inch Display ProcessorDescription Place in 8000i SystemMounting Power requirementsNorthstar 8000i Black Box Processor Location GuideNorthstar 8000i 15 inch Monitor Other parts required Northstar 8000i Network Radar Power requirements Voltage Fuse DrawFunctions Northstar 8000i 8 Port Network Linker Northstar 8000i 4 Port USB Hub Functionality Northstar 8000i 1 kW Network SounderNorthstar 8000i DVD-CD Player Northstar 8000i Remote Keypad Northstar 8000i Video Interface Northstar 8000i C-MAP Chart License KeyNorthstar GPS Antenna NS004743 Autopilot Other ComponentsAudio Heading SensorMounting and Calibration GLL NMEA-0183 DataGSA Mass Storage Devices Other Functions Location Guide Human Interface DevicesNetwork Camera Description Place in 8000i SystemChoosing the best mounting location Mounting the 8000i 12 inch Display ProcessorViewing Angle Page Page Wiring Guidelines Power Northstar 8000i Black Box 8000i System Power requirementsGPS Port Utility Port External Wake Up and Remote Power OnConnect this to the Light Green wire on Page Nmea Multiplexer Noland NM42 NmeaWiring Connect the following External AlarmPage USB Auxiliary port Network RGB portPage Field Terminated Network Cable Brown White/Brown Blue White/Green White/Blue Terminating a Northstar 8000i RJ45 Field Kit Before crimp After crimp Example System Layouts 8000i Chart Plotter8000i Plotter Sounder NS004743 Northstar GPS Antenna Entertainment Northstar 8000i Processor Full System Northstar Black Box Processor NS004730 Turn on the 12 inch Display Processor Northstar 8000i Initial SetupAdjust the brightness on a 12 inch Display Processor To adjust the backlight brightnessTo set the master Set the network master unitTo install all collections Install the chart dataInstall Charts interface To install chart collectionsTurn off the 12 inch Display Processor To turn the beeps on or off Set the system preferencesTo select the time format To select your time zoneTurn the keypad backlight on or off To change the transducer depthTo turn the backlight on or off Change the transducer depthSet the location of the media library To show or hide the top control barSpecify your vessel statistics To specify your vessel statisticsTo select Nmea Output sentences Set Nmea OutputSet the device processor name Set Nmea Baud RateCalibrate the touch screen To calibrate the touch screenSet the units Set the screen resolutionTo select the large scale distance units To select the volume units for liquidsTo select the small scale distance units Set up the radar before using it for the first time To select the temperature unitsTo set up the radar before using it Select the temperature unitsChange the radar startup mode To change the radar startup modeChange the radar range offset trigger delay Change the radar bearing alignment To change the radar range offsetTo change the radar bearing alignment To change the parking angleTo change the speed offset To change the offset for the water temperatureTo change the water temperature averaging time SounderCreate an instrument panel InstrumentsTo create an instrument panel Change the sounders speed filterResize an instrument To add a new instrumentTo resize an instrument To rename an instrument panelDelete an instrument panel To delete an instrument panelTechnical support, service and repairs MaintenanceTo restore the system processor RestoreRestore settings and information Restore processor softwareUpgrading the 8000i system There two types of upgrade for a 8000i processorSoftware patch multi-processor system Master Install a software patch to multi processor systemInstall a system image upgrade System image upgradeThirty minutes System will then restart automatically Display SpecificationsUnited States Europe Northstar