Belkin 8000I Northstar 8000i Initial Setup, Turn on the 12 inch Display Processor

Page 63

10 Northstar 8000i Initial Setup

When starting a multi-processor system for the first time. The following sequence should be followed.

1.Power on the master processor (see "Turn on the 12 inch Display Processor" page 63) and set to be the master (see "Set the network master unit" page 64) (ensure other processors are off). Take note of the master processor name. It will be a good idea to use the provided System Setup Check sheet. This will provide a record of the settings on install and serve as a reminder to check all settings.

2.Install purchased charts. (see "Install the chart data" page 65)

3.Configure System attributes such as time offset, draft, NMEA output etc.

4.Power on the next processor and nominate the master processor when prompted (this can be done form this processor or from the master). Setup the processor. Repeat till all processors are on and configured.

5.Start one processor at a time nominating the system master when prompted (see "Set the network master unit" page 64)

10.1Turn on the 12 inch Display Processor

Just press the Power key to turn on the 8000i. The Northstar 8000i screen appears briefly, followed by the Chart screen in a single pane. The 8000i is ready to use. Refer to the Northstar 8000i System Operation Manual for instructions on how to use the 8000i System.

When starting for the first time. the system will prompt you to nominate master processor (see "Set the network master unit" page 64).

10.2Adjust the brightness on a 12 inch Display Processor

The brightness on the 8000i can be adjusted to allow for various lighting situations. For night time, the backlight can be turned down to aid night vision.

To adjust the backlight brightness

1.Briefly press the 8000i processor power key to bring up the onscreen display.

2.Select brightness control.

3.Use the rotary knob to adjust the brightness, then either:

wait until the 8000i exits the onscreen display automatically, or

select the Exit option (using the down arrow) then press the Confirm key.

Northstar 8000i System - 12" Display Processor Installation Manual

63

Image 63

Contents Northstar Important Safety Information PrefacePlease read carefully before use Ft 0.5 m Disclaimer WarrantyContents Example System Layouts Maintenance Check the 12 inch Display Processor parts Introducing the Northstar 8000i SystemChart License Key NS004820 Page PPI Find your way around the 12 inch Display ProcessorRGB Network Master Unit Installation Sequence Summary Guidelines 8000i System InstallationOptional Parts Northstar 8000i 12 inch Display ProcessorDescription Place in 8000i SystemMounting Power requirementsNorthstar 8000i Black Box Processor Location GuideNorthstar 8000i 15 inch Monitor Other parts required Power requirements Voltage Fuse Draw Northstar 8000i Network RadarFunctions Northstar 8000i 8 Port Network Linker Northstar 8000i 4 Port USB Hub Functionality Northstar 8000i 1 kW Network SounderNorthstar 8000i DVD-CD Player Northstar 8000i Remote Keypad Northstar 8000i Video Interface Northstar 8000i C-MAP Chart License KeyNorthstar GPS Antenna NS004743 Autopilot Other ComponentsHeading Sensor AudioMounting and Calibration GLL NMEA-0183 DataGSA Mass Storage Devices Other Functions Location Guide Human Interface DevicesNetwork Camera Description Place in 8000i SystemChoosing the best mounting location Mounting the 8000i 12 inch Display ProcessorViewing Angle Page Page Wiring Guidelines Power Northstar 8000i Black Box 8000i System Power requirementsGPS Port Utility Port External Wake Up and Remote Power OnConnect this to the Light Green wire on Page Nmea Multiplexer Noland NM42 NmeaWiring Connect the following External AlarmPage USB Auxiliary port Network RGB portPage Field Terminated Network Cable Brown White/Brown Blue White/Green White/Blue Terminating a Northstar 8000i RJ45 Field Kit Before crimp After crimp Example System Layouts 8000i Chart Plotter8000i Plotter Sounder NS004743 Northstar GPS Antenna Entertainment Northstar 8000i Processor Full System Northstar Black Box Processor NS004730 Turn on the 12 inch Display Processor Northstar 8000i Initial SetupAdjust the brightness on a 12 inch Display Processor To adjust the backlight brightnessTo set the master Set the network master unitTo install all collections Install the chart dataInstall Charts interface To install chart collectionsTurn off the 12 inch Display Processor To turn the beeps on or off Set the system preferencesTo select the time format To select your time zoneTurn the keypad backlight on or off To change the transducer depthTo turn the backlight on or off Change the transducer depthSet the location of the media library To show or hide the top control barSpecify your vessel statistics To specify your vessel statisticsTo select Nmea Output sentences Set Nmea OutputSet the device processor name Set Nmea Baud RateCalibrate the touch screen To calibrate the touch screenSet the units Set the screen resolutionTo select the volume units for liquids To select the large scale distance unitsTo select the small scale distance units Set up the radar before using it for the first time To select the temperature unitsTo set up the radar before using it Select the temperature unitsTo change the radar startup mode Change the radar startup modeChange the radar range offset trigger delay Change the radar bearing alignment To change the radar range offsetTo change the radar bearing alignment To change the parking angleTo change the speed offset To change the offset for the water temperatureTo change the water temperature averaging time SounderCreate an instrument panel InstrumentsTo create an instrument panel Change the sounders speed filterResize an instrument To add a new instrumentTo resize an instrument To rename an instrument panelDelete an instrument panel To delete an instrument panelTechnical support, service and repairs MaintenanceTo restore the system processor RestoreRestore settings and information Restore processor softwareUpgrading the 8000i system There two types of upgrade for a 8000i processorSoftware patch multi-processor system Master Install a software patch to multi processor systemInstall a system image upgrade System image upgradeThirty minutes System will then restart automatically Display SpecificationsUnited States Europe Northstar