Belkin 8000I installation manual Restore settings and information, Restore processor software

Page 82

12 Restore

12.1Restore settings and information

You can restore the:

global settings that are stored on the master unit. This option deletes all the changes that you've made and resets all the display units in your 8000i System local settings. This option affects only the display unit that you're currently using routes, tracks, and waypoints information if the data has been corrupted.

12.2Restore processor software

This function will restore the operating system firstly back to factory defaults the it will apply any software patches that have been installed post factory.

To restore the system processor:

1.Start the Northstar 8000i System processor

2.Select Restore

3.Wait for the Northstar 8000i Installation environment to start. This can take up to five minutes.

4.To restore the system select Recover / Restore Current Version

5.To upgrade, select the source listed on the screen (this could be the DVD drive or other mass storage device that the upgrade file is located on).

6.The system will prompt you to confirm. Select Yes.

7.The upgrade files will be copied across to the 8000i processor. This will take approximately five to six minutes

8.Once this is done the system will reboot automatically and the files are installed into the system, this should take approximately four to five minutes.

9.A message appears: "System resealed OK to Reboot?" Select OK.

10.The system will restart and the Northstar 8000i screen will appear. This will take up to three minutes for the first time following a upgrade.

Northstar 8000i System - 12" Display Processor Installation Manual

82

Image 82

Contents Northstar Preface Important Safety InformationPlease read carefully before use Ft 0.5 m Warranty DisclaimerContents Example System Layouts Maintenance Introducing the Northstar 8000i System Check the 12 inch Display Processor partsChart License Key NS004820 Page Find your way around the 12 inch Display Processor PPIRGB Network Master Unit 8000i System Installation Installation Sequence Summary GuidelinesPlace in 8000i System Northstar 8000i 12 inch Display ProcessorDescription Optional PartsLocation Guide Power requirementsNorthstar 8000i Black Box Processor MountingNorthstar 8000i 15 inch Monitor Other parts required Northstar 8000i Network Radar Power requirements Voltage Fuse DrawFunctions Northstar 8000i 8 Port Network Linker Northstar 8000i 4 Port USB Hub Northstar 8000i 1 kW Network Sounder FunctionalityNorthstar 8000i DVD-CD Player Northstar 8000i Remote Keypad Northstar 8000i C-MAP Chart License Key Northstar 8000i Video InterfaceNorthstar GPS Antenna NS004743 Other Components AutopilotAudio Heading SensorMounting and Calibration NMEA-0183 Data GLLGSA Mass Storage Devices Description Place in 8000i System Human Interface DevicesNetwork Camera Other Functions Location GuideMounting the 8000i 12 inch Display Processor Choosing the best mounting locationViewing Angle Page Page Wiring Guidelines Power 8000i System Power requirements Northstar 8000i Black BoxGPS Port External Wake Up and Remote Power On Utility PortConnect this to the Light Green wire on Page Nmea Nmea Multiplexer Noland NM42Wiring External Alarm Connect the followingPage USB Auxiliary port RGB port NetworkPage Field Terminated Network Cable Brown White/Brown Blue White/Green White/Blue Terminating a Northstar 8000i RJ45 Field Kit Before crimp After crimp 8000i Chart Plotter Example System Layouts8000i Plotter Sounder NS004743 Northstar GPS Antenna Entertainment Northstar 8000i Processor Full System Northstar Black Box Processor NS004730 To adjust the backlight brightness Northstar 8000i Initial SetupAdjust the brightness on a 12 inch Display Processor Turn on the 12 inch Display ProcessorSet the network master unit To set the masterTo install chart collections Install the chart dataInstall Charts interface To install all collectionsTurn off the 12 inch Display Processor To select your time zone Set the system preferencesTo select the time format To turn the beeps on or offChange the transducer depth To change the transducer depthTo turn the backlight on or off Turn the keypad backlight on or offTo specify your vessel statistics To show or hide the top control barSpecify your vessel statistics Set the location of the media librarySet Nmea Output To select Nmea Output sentencesTo calibrate the touch screen Set Nmea Baud RateCalibrate the touch screen Set the device processor nameSet the screen resolution Set the unitsTo select the large scale distance units To select the volume units for liquidsTo select the small scale distance units Select the temperature units To select the temperature unitsTo set up the radar before using it Set up the radar before using it for the first timeChange the radar startup mode To change the radar startup modeChange the radar range offset trigger delay To change the parking angle To change the radar range offsetTo change the radar bearing alignment Change the radar bearing alignmentSounder To change the offset for the water temperatureTo change the water temperature averaging time To change the speed offsetChange the sounders speed filter InstrumentsTo create an instrument panel Create an instrument panelTo rename an instrument panel To add a new instrumentTo resize an instrument Resize an instrumentTo delete an instrument panel Delete an instrument panelMaintenance Technical support, service and repairsRestore processor software RestoreRestore settings and information To restore the system processorThere two types of upgrade for a 8000i processor Upgrading the 8000i systemSystem image upgrade Install a software patch to multi processor systemInstall a system image upgrade Software patch multi-processor system MasterThirty minutes System will then restart automatically Specifications DisplayUnited States Europe Northstar