Belkin 8000I Install a software patch to multi processor system, Install a system image upgrade

Page 84

7.Select Software Upgrade

8.When the upgrade screen appears select OK to continue. or Cancel. (optionally use

the Tick or X on the keypad to continue or cancel)

9.When the system has finished copying files you will be prompted to remove the USB pen drive and power down the processor

10.Start the processor for the changes to take effect

13.2Install a software patch to multi processor system

Software patch: multi-processor system MASTER

1.Upgrade the Software on the Master Processor First as outlined above. if you don't want to upgrade the other processors at this stage power them down before upgrading the master.

NOTE: All processors on the network must have the same software version. Once the master has being upgraded, all other units wont function until they have being upgraded

Software patch: multi-processor system Client.

1.Once the master has been upgraded. Power up the client processor. The upgrade will commence automatically. Files will be copied from the master and installed on to the client.

2.If the client processor was running when the master was upgraded it will display am message saying the software is incompatible with the master and prompt you to upgrade. Power down the unit and restart. The upgrade will commence automatically

13.3Install a system image upgrade

System image upgrade

1.Start the 8000i processor and wait till system has finished loading and is running normally

2.Back up user settings (recommended)

3.Make sure there are no USB pen drives or other USB mass storage devices attached to the system. This can cause problems and possibly result in a mass storage device losing its data

4.Start the 8000i processor and wait till system has finished loading and is running normally

5.Make sure the 8000i DVD is connected to the processor being upgraded. Insert the image DVD (this can be obtained from your Northstar dealer.

6.Select Display.

7.Select Installation.

8.Select Software upgrade

9.Acknowledge that there is no software upgrade available and go to image upgrade page by selecting OK

Northstar 8000i System - 12" Display Processor Installation Manual

84

Image 84

Contents Northstar Important Safety Information PrefacePlease read carefully before use Ft 0.5 m Warranty DisclaimerContents Example System Layouts Maintenance Introducing the Northstar 8000i System Check the 12 inch Display Processor partsChart License Key NS004820 Page Find your way around the 12 inch Display Processor PPIRGB Network Master Unit 8000i System Installation Installation Sequence Summary GuidelinesNorthstar 8000i 12 inch Display Processor DescriptionPlace in 8000i System Optional PartsPower requirements Northstar 8000i Black Box ProcessorLocation Guide MountingNorthstar 8000i 15 inch Monitor Other parts required Power requirements Voltage Fuse Draw Northstar 8000i Network RadarFunctions Northstar 8000i 8 Port Network Linker Northstar 8000i 4 Port USB Hub Northstar 8000i 1 kW Network Sounder FunctionalityNorthstar 8000i DVD-CD Player Northstar 8000i Remote Keypad Northstar 8000i C-MAP Chart License Key Northstar 8000i Video InterfaceNorthstar GPS Antenna NS004743 Other Components AutopilotHeading Sensor AudioMounting and Calibration NMEA-0183 Data GLLGSA Mass Storage Devices Human Interface Devices Network CameraDescription Place in 8000i System Other Functions Location GuideMounting the 8000i 12 inch Display Processor Choosing the best mounting locationViewing Angle Page Page Wiring Guidelines Power 8000i System Power requirements Northstar 8000i Black BoxGPS Port External Wake Up and Remote Power On Utility PortConnect this to the Light Green wire on Page Nmea Nmea Multiplexer Noland NM42Wiring External Alarm Connect the followingPage USB Auxiliary port RGB port NetworkPage Field Terminated Network Cable Brown White/Brown Blue White/Green White/Blue Terminating a Northstar 8000i RJ45 Field Kit Before crimp After crimp 8000i Chart Plotter Example System Layouts8000i Plotter Sounder NS004743 Northstar GPS Antenna Entertainment Northstar 8000i Processor Full System Northstar Black Box Processor NS004730 Northstar 8000i Initial Setup Adjust the brightness on a 12 inch Display ProcessorTo adjust the backlight brightness Turn on the 12 inch Display ProcessorSet the network master unit To set the masterInstall the chart data Install Charts interfaceTo install chart collections To install all collectionsTurn off the 12 inch Display Processor Set the system preferences To select the time formatTo select your time zone To turn the beeps on or offTo change the transducer depth To turn the backlight on or offChange the transducer depth Turn the keypad backlight on or offTo show or hide the top control bar Specify your vessel statisticsTo specify your vessel statistics Set the location of the media librarySet Nmea Output To select Nmea Output sentencesSet Nmea Baud Rate Calibrate the touch screenTo calibrate the touch screen Set the device processor nameSet the screen resolution Set the unitsTo select the volume units for liquids To select the large scale distance unitsTo select the small scale distance units To select the temperature units To set up the radar before using itSelect the temperature units Set up the radar before using it for the first timeTo change the radar startup mode Change the radar startup modeChange the radar range offset trigger delay To change the radar range offset To change the radar bearing alignmentTo change the parking angle Change the radar bearing alignmentTo change the offset for the water temperature To change the water temperature averaging timeSounder To change the speed offsetInstruments To create an instrument panelChange the sounders speed filter Create an instrument panelTo add a new instrument To resize an instrumentTo rename an instrument panel Resize an instrumentTo delete an instrument panel Delete an instrument panelMaintenance Technical support, service and repairsRestore Restore settings and informationRestore processor software To restore the system processorThere two types of upgrade for a 8000i processor Upgrading the 8000i systemInstall a software patch to multi processor system Install a system image upgradeSystem image upgrade Software patch multi-processor system MasterThirty minutes System will then restart automatically Specifications DisplayUnited States Europe Northstar