DeWalt DCR018 To Install Coin Cell Battery FIG, POWER/VOLUME Adjustment FIG, Mode Function FIG

Page 11

For more information regarding fuel gauge battery packs, please call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt. com.

TO INSTALL COIN CELL BATTERY (FIG. 5)

WARNING: Danger of explosion if battery is

3V X 1

incorrectly replaced. When replacing battery,

 

replace it with the same or equivalent type

 

CR2032. Observe correct polarity (+ and –) when

 

replacing batteries. Do not store or carry batteries

CR2032

so that metal objects can contact exposed battery

 

terminals.

 

Your radio is equipped with memory capacity in order to store the time and your selected radio stations. When the radio is in the OFF position, this memory capacity is powered by one coin cell battery that is included with the radio.

DANGER: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

POWER/VOLUME ADJUSTMENT (FIG. 6)

 

1. To turn the radio on and off, press the FIG. 6

A

ON/OFF button (A).

 

2. Turn the dial (B) clockwise to increase the volume. To decrease the volume, turn the dial counterclockwise.

English

1.Turn the screw on the battery door (L) counterclockwise to remove. Screw will remain captive in the door.

2.Press down on the battery door latch and pull to open.

3.Install the coin cell battery (M).

4.Replace the battery door, insert the screw and tighten it clockwise.

FIG. 5

M

L

MODE FUNCTION (FIG. 1)

To choose one of the mode functions (FM1, FM2, AM, or AUX) push the mode button (F) until the desired function is found. For example, if the radio is on FM1, seen in upper left portion of LCD display (I), push the mode button three times to change to AUX.

TUNE OR SEEK FUNCTION (FIG. 1)

There are two tuning methods and one seek method for finding the desired frequency.

NOTE: Put the antenna in the raised position for the best possible

NOTE: To reset the LCD display, clock, and pre-sets, remove the coin cell battery and re-install. Follow this procedure if the screen seems to lock in place.

reception.

To tune:

Briefly press and release the right or left arrow button (E) once to increment the frequency up or down.

9

Image 11
Contents DCR018 Page DCR018 Heavy-Duty Compact Work Site Radio Definitions Safety GuidelinesImportant Safety Instructions Regulatory Notices Read ALL Instructions Important Safety Instructions for All Battery PacksRbrc Seal Important Safety Instructions for All Battery ChargersNever attempt to connect 2 chargers together Chargers Charging Procedure FigIndicator Light Operation Charge IndicatorsFor Future USE Important Charging NotesStorage Recommendations Operation Installing and Removing the Battery Pack FigFuel Gauge Battery Packs FIG Components FIGTune or Seek Function FIG To Install Coin Cell Battery FIGPOWER/VOLUME Adjustment FIG Mode Function FIGImportant Radio Notes Device Storage Box FigRegister Online MaintenanceCleaning Accessories Repairs Three Year Limited WarrantyDAY Money Back Guarantee Year Free ServiceYears Free Service on Dewalt Battery Packs Dewalt Battery PacksConsignes de sécurité importantes Définitions lignes directrices en Matière de sécuritéRadio industrielle compacte de chantier DCR018 Normes Lire Toutes LES Consignes Toutefois, si le joint d’étanchéité extérieur est rompu Conserver CES Instructions Le sceau SrprcmcAmpères Voyants de charge Fonctionnement du voyantChargeurs Procédure de charge FigLaisser LE BLOC-PILES Dans LE Chargeur Remarques importantes concernant le chargementUtilisation Recommandations de stockageInstallation et retrait du bloc-piles Fig Témoin DE Charge DU BLOC-PILES FIG Pour Installer UNE Pile Bouton FIGProgrammation DE L’HORLOGE FIG Réglage DE MARCHE/ARRÊT ET DU Volume FIGFonction DU Mode FIG Fonction DE Syntonisation OU DE Recherche FIGNettoyage AccessoiresRemarques importantes relatives à la radio Boîtier de rangement FigContrat D’ENTRETIEN Gratuit D’UN AN RéparationsRegistre en ligne Garantie limitée de trois ansGarantie DE Remboursement DE 90 Jours BLOCS-PILES DewaltInstrucciones de seguridad importantes Definiciones Normas de seguridadNotificaciones regulatorias LEA Todas LAS Instrucciones Sin embargo, si el sello externo está roto El sello RbrcGuarde Estas Instrucciones Procedimiento de carga Fig CargadoresPermanencia DE LA Unidad DE Batería EN EL Cargador Operación de la luz indicadora Indicadores de cargaNotas importantes sobre la carga Retardo POR Unidad CALIENTE/FRÍARecomendaciones de almacenamiento Unidades DE Batería CON Indicador DE Carga FIG OperaciónCómo instalar y retirar la unidad de batería Fig Función DE Sintonía O Búsqueda FIG ENCENDIDO/APAGADO Y Ajuste DE Volumen FIGPara Instalar LA Batería DE Botón FIG Función DE Modo FIGPara Programar EL Reloj FIG Caja de almacenamiento de dispositivos FigMantenimiento LimpiezaAccesorios Notas importantes sobre la radioPóliza de Garantía AÑO DE Servicio Gratuito Registro en líneaGarantía limitada por tres años ExcepcionesUnidades DE Batería Dewalt Copyright 2013 D Ewalt