Baldor MN1903 installation manual NextMove PCI Expansion card

Page 83

A Accessories A

A.1 Introduction

NextMove PCI is supplied with a software license to control 1, 2 ,3, 4 or 8 axes. Similarly, the NextMove PCI Expansion Card is supplied with a software license to control a further 4 or 8 axes. A license cannot be upgraded.

A.1.1 NextMove PCI Expansion card

The NextMove PCI Expansion Card is available in 4 or 8 axis variants and provides an additional 20 digital inputs, 12 digital outputs, 4 analog inputs, 4 analog outputs (drive command outputs) and a relay. However, there are no CAN functions. The electrical specification of the I/O is the same as the main NextMove PCI card. The card requires its own additional breakout module and 100-pin cable.

NextMove PCI supports either one or two expansion cards. Connection to the cards is made through a bridging PCB (the expansion interconnect) that connects across the top of the cards.

Figure 17 - NextMove PCI Expansion card

Note: If two expansion cards are used then the dual interconnect board is needed. It is advisable to exert a retaining force on the interconnect board, to prevent it working loose due to vibration.

MN1903

Accessories A-1

Image 83
Contents NextMove PCI Motion Controller Page Contents Operation Appendices Iv Contents MN1903 General Information Precautions Safety NoticeMN1903 Introduction NextMove PCI featuresIntroduction MN1903 Catalog number PCI001 InstalledReceiving and inspection Identifying the catalog numberUnits and abbreviations PhaseTools and miscellaneous hardware Other information needed for installationIntroduction Hardware requirementsLocation requirements NextMove PCI Expansion card and can Bracket board InstallationThis completes the basic installation Installing the NextMove PCI cardBasic Installation MN1903 Outline 100-pin edge connectorPin Signal 1 100-pin connector pin assignment100-pin connector pin assignment Analog I/O Pin Name MintMT keyword / description Analog inputsLocation Analog input wiring, AIN0 shown Pin Name Description Analog outputs Drive Demand/CommandDigital input arrangement Input Common Breakout module connectorDigital I/O Stepperio Pin Name MintMT keyword Common Description Digital inputsINX.4 Digital input circuit fast interrupts Digital outputs OUTX.0 Encoder interfaces X12, X13, X14, X15 Other I/OEncoder input frequency Power Relay connections Relay and can powerPin X10 Name X11 Name Description Stepper drive outputs X10Cable length Maximum bit Resistance Conductor Rate Area Can Connections1 CAN1 CANopen 2 CAN2 Baldor can Baldor proprietary can interface using a RJ45 connectorSystem watchdog Reset statesEmulator connection Example minimum system wiring Connection summary minimum system wiringBreakout Pin Name Function This completes the input/output wiringModule Signal Connector Connector details for minimum system wiring shown in FigureInput / Output MN1903 Drivers\nmPCI\win9x Installing the driver software Windows 95, 98 and MEInstalling the driver software Windows Installing the driver software Windows NT\start Installing WorkBenchStarting WorkBench MN1903 Operation Operation MN1903 Help file WorkBenchChoosing an axis 8 axis card Configuring an axisChoosing an axis 1, 2, 3 and 4 axis cards Selecting a scale Setting the drive enable output Testing the drive enable output Testing the drive command output Servo axis testing and tuningAn introduction to closed loop control Summary, the following rules can be used as a guide NextMove PCI servo loop Selecting servo loop gains Servo axis tuning for current controlMN1903 Operation Underdamped response Underdamped responseOverdamped response Overdamped responseCritically damped ideal response Critically damped responseServo axis eliminating steady-state errors Calculating Kvelff Servo axis tuning for velocity controlKvelff Correct value of Kvelff Adjusting Kprop Correct value of Kprop JOG.0=2 Stepper axis testingDigital input configuration Digital input/output configurationDigital output configuration Saving setup information 10.1Loading saved information Operation MN1903 SupportMet feature Problem diagnosisStatus and can LEDs NextMove PCI indicatorsMotor control Symptom CheckCommunication Output polarity Mechanical specifications Digital inputs X1 Encoder interfaces X12 Relay output11Baldor can interface Stepper outputs X1010CANopen interface NextMove PCI Expansion card NextMove PCI Expansion cardExpansion Expansion card Axis numbering when using expansion cardsMain Expansion cards With no One 4-axis One 8-axis Two 4-axisExpansion card status LEDs CBL021-503 NextMove PCI Breakout moduleCatalog number Description PCI003-501 CBL021-501Catalog Description Number OPT025-508 Digital output modulesNextMove PC system adapter SparesBaldor can nodes OPT029-501 NextMove PCI can Bracket boardEncoder Splitter/Buffer board Catalog Description Number OPT008-501Accessories MN1903