Omron HBP-1300 Installing the Optional Battery Pack, Battery life, Charging time, Low battery

Page 16

Installing the Optional Battery Pack

Warning

If battery fluid comes in contact with the eye, immediately flush with copious amounts of water. Do not rub. Seek medical attention immediately.

Do not use the optional battery pack in any other device besides this unit. Do not throw into flame, disassemble, or heat.

Caution

Do not short the positive and negative terminals of the optional battery pack with a wire or other metal object. If battery fluid comes into contact with the skin or clothes, immediately rinse with water.

1. Make sure the AC adapter has been disconnected.

2. Remove the two screws from the top of the rear unit cover, and remove the battery cover.

3. Connect the battery pack to the connector on the monitor, and insert the battery pack into the compartment so that the triangle mark on the battery pack is aligned with the triangle mark on the monitor.

4. Replace the battery cover and secure with screws.

Take care not to pinch the wires when replacing the cover.

5. Connect the AC adapter to the unit and charge the battery pack.

When using the battery pack for the first time, be sure to fully charge (about 4 hours) before using.

Battery life

About 300 measurements are possible with one charge.

A general guideline for replacement of the battery pack is about one year, however, the usage time per charge may grow shorter depending on usage conditions. If you find that the usage time after

each charge has grown shorter and the icon frequently appears, replace the battery pack.

Charging time

Charging automatically starts after the AC adapter is connected.

When a new battery pack or a battery pack that has not been used for a long time is used, some time may elapse before charging starts.

The icon flashes during charging.

Charging is completed in about 4 hours.

Low battery

When the

icon starts flashing, promptly charge the battery pack.

When the icon changes to

, the battery is too low for blood pressure measurement. Charge the

battery.

 

 

Auto Power Off

When the unit is powered by the optional battery pack, the power automatically turns off after the set time elapses if you forget to turn off the power.

When the unit is used with the AC adapter connected, the "Auto Power Off" setting does not operate.

14

Image 16
Contents HBP-1300 Page Intended Use IntroductionExemptions General Information Setup Usage warnings and cautionsBefore use / during use Page Cleaning Maintenance and inspectionOptional rechargeable battery Non-Invasive Blood Pressure Nibp measurement For cleaning, see Using the Unit Optional AccessoriesMain unit Standard accessories Components of the ProductFeatures of the Product Key features, benefits, lookCuff Hose 3.5 m Cuff Hose 1.5mMeaning of the Symbols Features / Functions of UnitFront and back of unit Only when the optional battery is installed Using the UnitLCD Display Installing the Optional Battery Pack Battery lifeLow battery Auto Power OffConnecting the AC Adapter Battery chargingBattery level AC powerSystem Settings Menu ModePress the Mode button Press the or button to change the settingUtility Mode Press the or button to change the auto power off settingCheck the Pressure Accuracy ExampleNon-Invasive Blood Pressure Nibp Measurement Non-Invasive Pressure Measurement PrinciplesConnecting the cuff Available as an optional accessoryCuff Selection and Connection Selecting the cuffAlign the artery mark Index Artery with the brachial artery Blood pressure measurement is performed once Measurement results are displayedFailure Taking the Measurement in Auscultation Mode Irregular pulse wave detection functionBody movement detection function Use a stethoscope to perform measurementDisplaying Last Reading Stopping the MeasurementIrregular pulse wave icon Appears Maintenance Maintenance Inspection and Safety ManagementDevice Maintenance Accessory CareBefore turning on the power When turning on the powerAfter turning on the power Check before UseTroubleshooting Abnormal measurement value StethoscopeMeasurement value is questionable List of Error Codes Error Priority Description Points to checkOther problems Error Priority Cause Solution CodeDisposal DescriptionLimited Warranty Call toll freeSpecifications Factory Default SettingsSpecifications BackupEnvironmental Conditions Power supplyNon-Invasive Blood Pressure Nibp Electromagnetic Immunity IEC60601-1-2 Manufacturers DeclarationEmission Test Compliance Electromagnetic Environment IEC60601-1-2 Electromagnetic Test level Recommend separation distancePage Recommended Separation Distances Separation distance according to frequency of transmitterPage Distributed by For Customer Service Call Toll FreeWest Field Court, Lake Forest, IL 60045, USA Made in China
Related manuals
Manual 38 pages 5.6 Kb