Invacare Top End T-3 manual Adjusting QUICK-RELEASE Axles Figure, REMOVING/INSTALLING Rear Wheels

Page 31

WHEELS

PROCEDURE 6

 

 

WARNING

Make sure the detent pin and locking pins of the quick/quad-release axle are fully released BEFORE operating wheelchair.

The locking pins MUST be protruding past the inside of the rear wheel axle bushing for a positive lock.

Keep locking pins clean.

4.If the locking pins are not protruding past the inside of the axle bushing or there is too much movement of the rear wheel assembly in a back and forth motion, refer to ADJUST- ING QUICK-RELEASE AXLES or ADJUSTING QUAD-RELEASE HANDLES in this proce- dure of the manual.

QUAD-RELEASE AXLE

Quad-Release Axle

Handle

Camber Insert

Detent Pin

Rear Wheel Hub

FIGURE 1 - REMOVING/INSTALLING REAR WHEELS

ADJUSTING QUICK-RELEASE AXLES (FIGURE 2)

1.Remove rear wheel and quick-release axle from chair.

2.Depress detent pin in the quick-release axle and slide axle through the wheel hub.

3.Release detent pin ensuring that locking pins are fully released.

4.Increase or decrease end play by adjusting knurled locking collar or locknut on the end of the quick-release axle.

WARNING

Make sure detent pin and locking pins of the quick-release axles are fully re- leased BEFORE operating the wheelchair.

Keep locking pins clean.

WHEELS

5. Reinstall rear wheel onto the chair.

Adjustable Axle Position

Camber Bar

Locking

Pins

NOTE: End of Quick Release axle is shown for reference only. It is not visible when in- serted into camber bar.

Quick

Locknut

Detent Pin

Wheel Hub

Release Axle

FIGURE 2 - ADJUSTING QUICK-RELEASE AXLES

Part No. 1054916

31

T-3™ and T-4™ Series

Image 31
Contents Owners Operator And Maintenance Manual Special Notes Special NotesTable of Contents Register Your Product Invacare Model No. Serial No Complete and mail this formName Address Zip/Postal Code Email Phone NoFold here Cut Along Line Typical Product Parameters Typical Product ParametersSee current order form 250 lbs See current order form Stability Warnings Procedure General GuidelinesStability General GuidelinesGeneral Warnings Continuted Weight Limitation Weight TrainingTire Pressure Stability and Balance SAFETY/HANDLING of WheelchairsPercentage of Weight Distribution Procedure General Guidelines Coping with Everyday ObstaclesShortening Front Adjustable Models OnlyFunctional Reach from a Wheelchair GuidelinesDo not tilt the chair without assistance TiltingStairways Transferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistSafety Inspection Safety Inspection Checklist Suggested Maintenance Procedures MaintenanceSafety Inspection Procedure Maintenance Safety PrecautionsBack ADJUSTING/REPLACING Back Upholstery FigureProcedure Back Adjusting Back UpholsteryReplacing Back Upholstery Folding Back Figure11-14 14-18 16-20 Back Height Adjustment FigureBack Angle Adjustment Figure Hole NumberBack Angle to Seat Rail Procedure Seat Seat Upholstery Replacement FigureSeat Rear Seat to Floor Range in Inches Rear Seat Height AdjustmentFront Seat Height Adjustment Before Front Seat Height AdjustmentClothing Nylon Clothing Guard with Plastic Insert Replacement FigureRigid Clothing Guard Replacement Figure Clothing GuardsQuick or QUAD-RELEASE Axles REMOVING/INSTALLING Rear Wheels FigureProcedure Wheels WheelsREMOVING/INSTALLING Rear Wheels Adjusting QUICK-RELEASE Axles FigureInstalling Figure INSTALLING/ADJUSTING QUAD-RELEASE AxlesAdjusting Quad-Release Handles In And/Or Out Adjusting FigureRemoving Play From Rear Wheels REPAIRING/REPLACING Rear WHEEL, TIRE/TUBE Handrim Replacement FigureDo not inflate tire until handrim is completely assembled QUICK-RELEASE Lever Standard Closed Position OPENING/CLOSING Clamps FigureOpen Position Wheelchair Determining TOE IN/TOE OUT FigureDetail a Measuring the Centerlines TOP View Wheelchair FrontCamber Inserts Adjusting TOE IN/TOE OUTOr 12 Camber Or 6/12 Camber InsertsWheels Axle Tube Will Rotate UP Only Elite and T-4 Models with Fixed Camber Figure Adjusting Rear Wheel Camber FigureRequired Camber Insert AdjustmentDetail a Measuring Frame Bracket Distance Adjusting Wheelbase Length Adjusting Center GravityAdjusting Wheelbase Width A-4 Camber Tube Adjusting Wheelbase Width FigureCamber Tube Replacing Axle Tube Figure Adjusting Wheelbase Width Camber TubeReplacing Axle Tube Adjusting Front Caster Height Figure Front Caster Replacement FigureInstalling Quick Release Casters Installing QUICK-RELEASE Casters FigureAdjusting the HIGH/LOW Mount Wheel Locks Wheel Lock ADJUSTMENT/REPLACEMENT FigureReplacing the HIGH/LOW Mount Wheel Lock Footrest Procedure FootrestWheelchair Frame Mounting Bracket Hex Screw Tennis Elite Individual Footplates Before 4/2000 Figures 2 Procedure Footrest Adjusting FootrestHeight Adjustment Depth AdjustmentRepositioning Footplate Footrest Procedure Changing Footplate AngleChanging Footplate Depth Changing Footplate HeightReplacing Footplate Mounting Bracket Procedure Footrest Removing FootplatesInstalling Footplates Removing Footplate System Mounting Clamp3 Tennis Elite Individual Footplates Footrest ProcedureAdjusting Individual Footplates Tennis Adjustable Footrest System Before 4/2000 FigureReplacing Individual Footplates Replacing Seat Adjustment Weldment Footrest Procedure Replacing Footplate WeldmentProcedure Footrest Elite and T-4 Elite with Fixed Camber Tube Figure REPLACING/ADJUSTING Fixed ANTI-TIPPER Swivel CasterOptional ANTI-TIPPER Procedure ReplacementAssembleddisassembled AdjustingOptional INSTALLING/ADJUSTING Removable ANTI-TIPPERANTI-TIPPER Anti-Tipper Push Mounting Holes Warranty WarrantyCanada