Invacare Top End T-3 OPENING/CLOSING Clamps Figure, QUICK-RELEASE Lever Standard Closed Position

Page 35

WHEELS	PROCEDURE 6

OPENING/CLOSING CLAMPS (FIGURE 6)

WARNING

QUICK RELEASE LEVERS - Make sure the quick-release levers are in the CLOSED position BEFORE using the wheelchair, otherwise personal injury or damage to the wheelchair may result.

STANDARD CAMBER CLAMPS - Make sure the hex screws and locknuts are securely tightened BEFORE using the wheelchair, otherwise personal injury or damage to the wheelchair may result.

CAUTION

A-4 CAMBER SYSTEM ONLY - DO NOT close the quick-release levers or tighten the hex screws and locknuts without camber inserts in the axle tube. Damage to the axle tube will occur.

1.Perform one (1) of the following to open a camber clamp:

A.QUICK-RELEASE LEVERS - Pull the quick-release lever to the open position.

B.STANDARD CAMBER CLAMPS - Loosen, but do not remove the hex screw and locknut on the camber clamp.

2.Perform one (1) of the following to close a camber clamp:

A.QUICK-RELEASE LEVERS - Push the quick-release lever on the camber clamps to the closed position.

B.STANDARD CAMBER CLAMPS - Securely tighten the hex screw and locknut to secure the axle tube.

QUICK-RELEASE LEVER

STANDARD

CLOSED

POSITION

Quick-Release

Lever

Hex Screw and Locknut

OPEN POSITION

FIGURE 6 - OPENING/CLOSING CLAMPS

WHEELS

Part No. 1054916

35

T-3™ and T-4™ Series

Image 35

Contents Owners Operator And Maintenance Manual Special Notes Special NotesTable of Contents Register Your Product Invacare Model No. Serial No Complete and mail this formName Address Zip/Postal Code Email Phone NoFold here Cut Along Line Typical Product Parameters Typical Product ParametersSee current order form 250 lbs See current order form Stability Warnings Procedure General GuidelinesStability General GuidelinesGeneral Warnings Continuted Tire Pressure Weight TrainingWeight Limitation Stability and Balance SAFETY/HANDLING of WheelchairsPercentage of Weight Distribution Procedure General Guidelines Coping with Everyday ObstaclesShortening Front Adjustable Models OnlyFunctional Reach from a Wheelchair GuidelinesDo not tilt the chair without assistance TiltingStairways Transferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistSafety Inspection Safety Inspection Checklist Suggested Maintenance Procedures MaintenanceSafety Inspection Procedure Maintenance Safety PrecautionsBack ADJUSTING/REPLACING Back Upholstery FigureProcedure Back Adjusting Back UpholsteryReplacing Back Upholstery Folding Back Figure11-14 14-18 16-20 Back Height Adjustment FigureBack Angle Adjustment Figure Hole NumberBack Angle to Seat Rail Seat Seat Upholstery Replacement FigureProcedure Seat Rear Seat to Floor Range in Inches Rear Seat Height AdjustmentFront Seat Height Adjustment Before Front Seat Height AdjustmentClothing Nylon Clothing Guard with Plastic Insert Replacement FigureRigid Clothing Guard Replacement Figure Clothing GuardsQuick or QUAD-RELEASE Axles REMOVING/INSTALLING Rear Wheels FigureProcedure Wheels WheelsREMOVING/INSTALLING Rear Wheels Adjusting QUICK-RELEASE Axles Figure Installing Figure INSTALLING/ADJUSTING QUAD-RELEASE AxlesRemoving Play From Rear Wheels Adjusting FigureAdjusting Quad-Release Handles In And/Or Out Do not inflate tire until handrim is completely assembled Handrim Replacement FigureREPAIRING/REPLACING Rear WHEEL, TIRE/TUBE Open Position OPENING/CLOSING Clamps FigureQUICK-RELEASE Lever Standard Closed Position Wheelchair Determining TOE IN/TOE OUT FigureDetail a Measuring the Centerlines TOP View Wheelchair FrontCamber Inserts Adjusting TOE IN/TOE OUTOr 12 Camber Or 6/12 Camber InsertsWheels Axle Tube Will Rotate UP Only Elite and T-4 Models with Fixed Camber Figure Adjusting Rear Wheel Camber FigureRequired Camber Insert AdjustmentDetail a Measuring Frame Bracket Distance Adjusting Wheelbase Length Adjusting Center GravityCamber Tube Adjusting Wheelbase Width FigureAdjusting Wheelbase Width A-4 Camber Tube Replacing Axle Tube Figure Adjusting Wheelbase Width Camber TubeReplacing Axle Tube Adjusting Front Caster Height Figure Front Caster Replacement FigureInstalling Quick Release Casters Installing QUICK-RELEASE Casters FigureReplacing the HIGH/LOW Mount Wheel Lock Wheel Lock ADJUSTMENT/REPLACEMENT FigureAdjusting the HIGH/LOW Mount Wheel Locks Footrest Procedure FootrestWheelchair Frame Mounting Bracket Hex Screw Tennis Elite Individual Footplates Before 4/2000 Figures 2 Procedure Footrest Adjusting FootrestHeight Adjustment Depth AdjustmentRepositioning Footplate Footrest Procedure Changing Footplate AngleChanging Footplate Depth Changing Footplate HeightReplacing Footplate Mounting Bracket Procedure Footrest Removing FootplatesInstalling Footplates Removing Footplate System Mounting Clamp3 Tennis Elite Individual Footplates Footrest ProcedureReplacing Individual Footplates Tennis Adjustable Footrest System Before 4/2000 FigureAdjusting Individual Footplates Replacing Seat Adjustment Weldment Footrest Procedure Replacing Footplate WeldmentProcedure Footrest Elite and T-4 Elite with Fixed Camber Tube Figure REPLACING/ADJUSTING Fixed ANTI-TIPPER Swivel CasterOptional ANTI-TIPPER Procedure ReplacementAssembleddisassembled AdjustingANTI-TIPPER INSTALLING/ADJUSTING Removable ANTI-TIPPEROptional Anti-Tipper Push Mounting Holes Warranty WarrantyCanada